Display gasket for the Clear-Com HXII-BP beltpack. Clear-Com 202G170 Display Gasket for HXII-BP.
Full Compass Systems
The Clear-Com IC-50 is a 50 ft intercom cable that features three-pin XLR-type connectors on each end. Clear-Com IC50 50 ft XLR to XLR Cable.
Full Compass Systems
The RAK850 Remote Antenna Kit allows you to relocate antennas away from the PRO850 base station for areas that experience RF reflection and dropouts.At times your professional audio equipment has to be located in areas that experience RF reflections and dropouts resulting from the excessive metal in the building. The RAK850 Remote Antenna Kit allows you to relocate antennas away from the PRO850 base station and away from the sources causing RF reflection and dropouts. This solution changes the transmission and reception patterns to overcome problem areas - extending the range and reception of the HME PRO850 Wireless Intercom System.The RAK850 includes a 30 foot cable with BNC connectors at both ends and a ground-plane surface (round metal disk) which is fitted with a thru-the-chassis BNC connector. For situations in which both antennas (RX and TX) have to be relocated, two RAK850 Remote Antenna Kits are required.Includes1-30 Foot (9.14 meter) cable with male BNC connector1-Ground Plane Surface (round metal disk) with bulkhead BNC adapterInstallation InstructionsFeaturesEasy Installation: The RAK850 Remote Antenna Kit is easy to install and quickly put into operation. No special tools other than the components of the antenna kit and an Allen wrench are required for installation.Extended Range: Extending one or both of the PRO850 antennas to a remote location away from the base station helps eliminate unwanted RF reflections and drop outs and improves system performance.Flexible & Low Cost: When your PRO850 communicators are experiencing communication problems, the RAK850 remedies the situation with a simple, low cost solution that protects the integrity of your audio operations. Clear-Com G24589-1 RAK850 Remote Antenna Kit.
Full Compass Systems
This USB AC charger is intended for use with FreeSpeak II beltpacks and comes with an international plug kit.Grab a spare, make sure you never run out of power. Clear-Com FSII-BP-USB-CHRGR FreeSpeak II USB Beltpack Charger with International AC Adap.
Full Compass Systems
Green and white 610-710 1/2 wave receiver antenna for these Clear-Com wireless intercom systems:WBS-670WBS-680 Clear-Com AND-680/GW FA-GW Antenna for WBS-670 and WBS-680.
Full Compass Systems
Belt clip for the Clear-Com CEL-BP beltpack.NoteThis replaces part# CEL-FS-CCLIP Clear-Com 251392Z CEL-BP Replacement Belt Clip.
Full Compass Systems
Clear-Com TWC703 TW Adapter for the RS703The TWC703 takes two single channels from a Clear-Com partyline and combines them to a TW line, allowing the addition of a dual channel TW segment to any Clear-Com partyline system. TW connectivity provides the system with the simplicity of standard 3-pin XLR cabling when using TW compatible user stations such as the RS-703 beltpack.Clear-Com TWC703 Features:Converts 2 Clear-Com partyline channels to 1 dual-channel TW partylineAuto power protectionAuto termination managementTranslates audio and call signalsWhen used with optional 453G042 Power Supply (sold separately):Independently powers TW outputStandalone dual channel TW PSUClear-Com TWC703 Specifications:Front Panel Connectors:2 x XLR3F Intercom In1 x XLR3M TW OutRear Panel Connector: 1 x 2.1mm coaxial DC power inputIndicators and controls:Front Panel: Power/Overload indicatorRear Panel: 2 x Call Translation on/off switches for channels A and BPower Requirements:Input Voltage: 20-360VDCInput Current (Idle): 65mAInput Current (Max): 550mATW Output Current (Max): 550mADimensions: 4” wide x 2” high x 5” deep (101 x 51 x 127 mm)Weight: 1.1 lbs. (0.503 kg)Operating Temperature: 32 to 122 degrees F (0 to 50 degrees C) Clear-Com TWC703 TW Adapter for the RS703.
Full Compass Systems
This single foam ear pad provides comfort and moderate isolation when using Clear-Com CC-110 (single sided) or CC-220 (double sided) headsets. Clear-Com 306G151 Foam Ear Pad for CC-110 and CC-220.
Full Compass Systems
The Clear-Com WH410 is a light-weight, single-ear, all-in-one wireless headset that operates in the 2.4GHz frequency range. This headset has a lightweight, balanced design and wire-free steel headband for all day comfort and is used with DX410 wireless system. The WH410 uses the BAT50 Li-Ion Batteries and AC50 Battery Charger.FeaturesTwo-channel2.4GHz frequency range7 kHz wide band audioUp to 15 beltpacks and/or all-in-one headsets on a single systemUp to 12 hours of battery lifeSpecificationsAudioChannels: 2 audio channelsFrequency Range: 2400 MHz – 2483.5 MHzFrequency Response: 200 Hz – 7 kHzAntenna: Internal, horizontal/vertical diversityHeadset Connector: 4-pin, mini-DINMicrophone: ElectretHeadset Output: 160mW into 32 OhmsCommunication Security: 64-bit encryptionSystem Distortion:Controls: Power, Volume-Up, Volume-Down, A, B, ISOIndicators: Dual-color LED (red/green)Battery Requirements: 3.6V lithium-ionBattery Life: Up to 12 hoursAntenna: InternalTransmitterType: Frequency Hopping, Spread Spectrum (FHSS)Transmit Power: 100mW burstModes: Momentary or LatchType: Gaussian filtered FSK, TDMAFrequency Stability: 13 ppmHarmonics/Spurious: Exceeds FCC and ETSI specificationsReceiverType: Frequency Hopping, Spread Spectrum (FHSS)RF Sensitivity:< -90dBm w 10-3 BERFrequency Stability: 13 ppmDistortion:< 2 %Environmentral: 32°F to +122°F (0°C to +50°C)Weight: 3.5 oz (0.10kg) including battery Clear-Com CZ-WH410 Wireless Headset.
Full Compass Systems
2-Way DX Antenna Splitter/Combiner. Clear-Com 647G006 2-Way DX Antenna Splitter / Combiner.
Full Compass Systems
Mini DIN-5PIN headset to pack cable for Clear-Com BP200 beltpack. Clear-Com 115G357 Headset to Pack Cable for BP200.
Full Compass Systems
Push talk switch for these Clear-Com models:CS-702MS-702MS-704SB-704RM-702RM-704KB-701KB-702 Clear-Com 672G091 Push Talk Switch for CS-702.
Full Compass Systems
Mic element with holder for the Clear-Com CC-110 and CC-220 headsets. Clear-Com 306G136 Mic Element for CC-110 and CC-220.
Full Compass Systems
Provides a visual and/or audible signal of a "call" when integrated to a Clear-Com or compatible intercom system.FeaturesBrightness level for FlasherVolume level for ToneChoose Flash, Tone, or Both Clear-Com FL7 Call Signal Flasher.
Full Compass Systems
Left knob for the Clear-Com FSII FreeSpeak II beltpack. Clear-Com 272G273 Left Knob for FSII.
Full Compass Systems
Pair of rack ears for these Clear-Com digital intercoms:HMS-4XHRM-4X Clear-Com HELIXNET-SER-2RE Rack Ear Set (Pair) for HMS-4X, HRM-4X.
Full Compass Systems
Clear-Com's CC-26K-CUSZ is a replacement single earpad cushion for their CC-26K headset. Clear-Com CC-26K-CUSZ Earpad for CC26K.
Full Compass Systems
CellCom/FreeSpeak replacement PC to beltpack programming cable by Clear-Com. Clear-Com PD4007Z Replacement PC to Beltpack Programming Cable.
Full Compass Systems
As your needs change you'll need to expand your HelixNet system. This license provides an upgrade for HelixNet main stations running 3.0 firmware to double the channel capacity from 12 to 24. Clear-Com HMS-24-UG Firmware Upgrade Charge to Expand HMS-4X Main Station Channel.
Full Compass Systems
The Clear-Com HS-6 is a Telephone-style Intercom handset featuring a push-to-talk switch in the handle which minimizes bleed of external sound into the intercom system when handset is not in use. It connects to the intercom station with 4-pin connector on a 6-foot coiled cord. A wall/console-mounting cradle is included.ApplicationsFull-duplex link to intercom system for less-frequent user or for more conventional lookFeaturesTelephone-style HandsetIncludes wall/console mount hangerPush-to-talk switch6-foot coil cord4-pin female XLR connectorDynamic microphoneSpecificationsMicrophone/Earpiece Transducer Type: Dynamic/DynamicMic/Earpiece Impedance: 800 Ω/200 ΩPush-to-Talk Switch: YesCable Type and Length: Coiled 3-wire plus shield, 6ft (1.85 m)Connectors: 4-pin XLR femaleWeight: 12 oz. (330 g) Clear-Com HS-6 Telephone-Style Intercom Handset.
Full Compass Systems
Main circuit board assembly for the Clear-Com HXII-BP digital intercom. Clear-Com T12216-1A1 Main PCB Assembly for HXII-BP.
Full Compass Systems
This software license will upgrade the beltpack capacity of an FSII-BASE-II-5 base unit from 5 beltpacks to 25 beltpacks. Clear-Com FSII-BASE-II-25BP-LICENSE License Upgrade to 25 Belt Packs.
Full Compass Systems
The Clear-Com CC-300 (single-ear) headset is a high-performance unit that features a single high ambient-noise attenuation earpiece plus a dynamic cardioid microphone that provides high-quality, top-of-the-line audio. Its soft ear pad combined with full adjustability offers ultimate comfort over long periods. Simply moving the 300° rotating mic boom up and down toggles the on/off microphone mute, while the gooseneck design allows for perfect positioning. The cable terminates in a 4-pin female XLR connector.Feature300áµ boom swivel allows left or right hand mic setupBoom rotation ON/OFF switch for quick microphone muting40 Hz - 20 kHz frequency responseInterchangeable cabling for easy connector changing and repairLeatherette Ear padsSpecificationsDriver: 40mm diameter, neodymium magnet, copper-clad aluminium wire voice coilHeadphone Frequency Response: 40 Hz - 20 kHzWeight: 245 gLeatherette EarpadsDynamic MicrophoneHypercardioid polar patternMicrophone Frequency Response: 300 Hz - 20 kHzOpen Circuit Sensitivity: -61.0 dB ±3.5 dB; at 1 kHz, typicalSensitivity: 102 dB ±3 dB; at 1kHz typicalHeadphone Impedance: 400 Ω ±30%; at 1 kHz typicalMicrophone Impedance: 200 Ω ±30%; at 1 kHz typicalCable: 5ft (1.55m) long with 8-pin connector at headset end; 4-pin XLR-Fat opposite endPackaging Dimensions (W x H x D): 4.8" x 13" x 10.43" (122 x 330 x 265mm)Weight: 8.6 oz. (245 g) without 8-pin cable assembly and M3*18mm screw Clear-Com CC-300-X4 Single-Ear Headset with 4-Pin XLR-F Connector.
Full Compass Systems
Earpad for these Clear-Com headsets:WH200WH210WH300HS12 Clear-Com 306G108 Earpad for WH200, WH210, WH300.
Full Compass Systems
Headband assembly for the Clear-Com CC-400 double-ear headset. Clear-Com 506104Z Headband Assembly for CC-400.
Full Compass Systems
Programmed DSP circuit board for the Clear-Com V-Series intercom systems. Clear-Com T10157-1A1 Programmed DSP PCB for V-Series.
Full Compass Systems
Clear-Com's Ethernet Linking Module HLI-ET2 plugs into any available slots on a HelixNet Main Station providing a dual LAN interface to connect to other Main Stations. RJ-45 connectors allow up to three HMS-4X Main Stations to be linked together forming a complete system. The HLI-ET2 can also be used to connect with HRM-4X remote stations, HKB-2X speaker stations, and HXII-BP belt packs to HMS-4X Main Stations with all labels transferred across all systems automatically. In addition, all digital partyline, program audio and 2 and 4-wire audio will be shared with all HelixNet stations.FeaturesEthernet LAN Network Interface ModuleLink up to 3 HMS-4X main stations over IPLink up to 3 LQ Series devices providing additional interfacing to both I/O and Agent-ICConnect HRM-4X remote stations, HKB-2X speaker stations and HXII-BP beltpacks to HMS-4X main stations over IPConnect IKB-12P Industrial speaker stations to HMS-4X main stationsAll labels transfer across linked systemsMix Ethernet and Fiber modules together within the same networkTwo RJ45 connectors per moduleSpecificationsDimensions: 7.36" W x 2.24" H x 1.54" D (187 x 57 x 39 mm)Weight: 13 oz (0.35 kg)Connectors: LAN 1 and 2: (2) RJ-45 (Ethercon)LAN Network Connection: 10/100 BaseT, DHCP Capable Clear-Com HLI-ET2 HelixNet Ethernet Linking Interface Module.
Full Compass Systems
A base station for use with the DX410 wireless system, the BS410 from Clear-Com operates in the 2.4 GHz frequency band with high-quality 7 kHz wideband audio, and supports up to 15 registered BP410 beltpacks and/or WH410 all-in-one wireless headsets (all sold separately). Audio bridging capable together on A or B channels.The BS410 is a 1RU 2-channel world-wide rated base station with local headset, 2- and 4-wire audio connections, auxiliary in out, and assignable relays. 2-wire connections and can be set to RTS or Clear-Com and have auto-nulling. The built in 2.4GHz transceiver transmits RF via two dipole antennas with reverse TNC connectors.Clear-Com BS410 Features:2-wire auto-nullingUpgraded radioLost packet concealmentRadio Frequency Range: 2400 – 2483.5 MHzCommunication Security: dual-slot diversityFrequency Hopping, Spread Spectrum (FHSS), Transmitter and ReceiverSupports up to 15 beltpacks in a single system (beltpacks sold separately)Clear-Com BS410 Specifications:Note: specifications and further information can be found within the items located under the "Documentation" tab above. Clear-Com BS410 DX410 System Base Station.
Full Compass Systems
The 306G145 is a foam windscreen/pop filter intended for use with Clear-Com CC-110 and CC-220 headset microphones. This filter will make speech more intelligible so keep a spare on-hand just in case. Clear-Com 306G145 Foam Pop Filter for CC-110 and CC-220.
Full Compass Systems
The CC-110-B6 features a dynamic cardioid microphone offering rejection of off-axis sounds generated from the back and sides in noisy environments. The integrated temple pad and adjustable headband were designed to provide comfort during long periods of use. This light-weight single-ear closed-back headset comes with a removable cable, allowing for quick connector changes or in the field repairs. For convenience, the CC-110s flexible boom arm acts as an on/off mute by simply moving the arm up or down. The boom arm can also be rotated so you can wear the headset on the left or right side for flexibility. You'll also get both leatherette and foam earpads, so you can tailor the earcup to your situation and comfort level.The B6 designation means this headset arriveswithout a connector.FeaturesLight-weightCardioid microphone for off axis rejectionClosed-back on-ear designflexible mic boom armInterchangeable cableBoom arm acts as an on/off mute switchComes with both leatherette and foam earpadsSpecificationsHeadphoneType: Closed-backDriver: 36mm diameter, neodymium magnet, copper-clad aluminum wire voice coilFrequency Response: 20Hz v- 20kHzMicrophoneElement: DynamicDriver: 15mm, neodymium magnetPolar Pattern: CardioidFrequency Response: 250Hz – 20kHzSensitivityOpen Circuit Sensitivity: -64 dB ±3.5 dB; at 1kHz, typical99 dB ±3 dB (SPL); at 1kHz typicalPowerMaximum: 500mWConnectorCable: 5ft (1.55m) long with 8-pin connector at headset end;Impedance400 ohms ±30%; at 1kHz typicalDimensionsPackaging for CC-110:6.7 x 8 x 3.5 in (WxHxD)(170 x 205 x 90 mm)Weight5.1 oz (145g) without 8-pin cable assembly and M3*18mm SCREW Clear-Com CC-110-B6 Lightweight Single Ear Headset, Unterminated.
Full Compass Systems
Supporting up to four FreeSpeak II beltpacks, Clear-Com's FSII-TCVR-24-US is an active transceiver antenna powered either locally or from the matrix CAT5 connection. Operating the in 2.4 GHz frequency band, the FSII-TCVR-24 has a mount for wall or microphone stand and comes with an IP-65 rating for wet weather and dusty conditions making it ideal for outdoor productions.The FSII-TCVR-24 has a mount for wall or microphone stand. A blue status light is visible from either mounting orientations. When mixed with FSII-TCVR-19 antennas, a single radio space can support up to 65-90 FreeSpeak II 1.9GHz or 2.4GHz beltpacks.NOTE:Approved for use in the US, Canada and Mexico.FeaturesUses existing FSII base, E-QUE-HX cards, and PD2203 splitter hardwareSupports 4 FSII-BP24 beltpacks per FSII-TCVR-24 transcieverSupports systems with up to 65-90 beltpacks when mixed with FSII-19-TCVRsBlue LED status indicator on top and bottomMic stand or wall mount orientation (metric and imperial threads)IP-65 rating for wet and dusty conditionsSpecificationsFrequency Spectrum: 2.400-2.483MHz for EU and US Cellular auto roaming technologyModulation: GFSK, TDMA frame 10ms Full slotOutput power: (EU): 18dBm, (RoW): 22dBmEnvironmental:IP-65 water and dust resistance-67°F to +158°F (-55°C to +70°C)Dimensions (D x W x H): 2 x 5.5 x 6.75" (52 x 134 x173 mm)Weight: 7.0 oz (0.19 kg) Clear-Com FSII-TCVR-24-US FreeSpeak II 2.4 GHz Active Antenna.
Full Compass Systems
Simplify the desktop or surface mounting of your HelixNet Speaker Station (sold separately) with the HelixNet Speaker Station Enclosure. Offering adjustable angles to suit a wide variety of deployment needs, this flexible enclosure is ideal for both portable and semi-permanent installations, providing multiple angles for optimal use. It features various connectivity options, making it easy to integrate into your current setup and ensuring reliable performance in any environment.Clear-Com HXII-MOUNT Includes:(4) 6/32 x 1/2" mounting screws (280038Z)(4) Screw cover (416G054)(4) Rubber feet (111G032)(1) Wall adapter PSU 15W 48V DC (453G025)Clear-Com HXII-MOUNT Features:Flexible enclosure for Speaker StationDesktop with multiple anglesPortable and semi-permanent installationsVarious connectivity optionsClear-Com HXII-MOUNT Specifications:ConnectorsXLR Powerline: 3-pin XLR-M/FDC Power: 3-pin KPJX-PM-3-SEthernet/PoE: RJ45PowerAC Adapter Wall (included):Input Voltage Range: 100 - 240V ACInput Frequency Range: 50 - 60HzInput Power Connector: UniversalOutput Voltage: 48V DCOutput Power (Max): 15WOutput Power Connector: KPPX-3-PEnvironmental32º - +104ºF (0º - +40ºC)90% relative humidityDimensionsMinimum (Closed):3.9 x 10.4 x 6.7 in (HxWxD)(99 x 265 x 170 mm)Maximum (Open):6.9 x 10.4 x 6.7 in (HxWxD)(175 x 265 x 170 mm)WeightHXII-MOUNT: 1.9lbs (0.86kg)S-MOUNT: 2.8lbs (1.2kg) Clear-Com HXII-MOUNT HelixNet Speaker Station Enclosure for Desk/Wall Surface Mounting with Adjustable Angles (Formerly S-MOUNT).
Full Compass Systems
Volume encoder for Clear-Com CP-922A beltpack. Clear-Com 674G009 Volume Encoder for CP-922A.
Full Compass Systems
Main circuit board assembly for the Clear-Com RS-703 beltpack. Clear-Com T10955-2 Main PCB for RS-703.
Full Compass Systems
The one rack unit RMK200 mounting kit is used for remote mounting of base antennas and includes two 2' cables.NotesMounting kit only, antennas not included. Clear-Com G28066-1 RMK200 1RU Mounting Kit.
Full Compass Systems
Maintaining comfort is essential during periods of extended use so you'll want to replace worn temple pads on your CC-110 headsets with the 306G146 foam pad. Clear-Com 306G146 Foam Temple Pad for CC-110.
Full Compass Systems
Hanger from Clear-Com for HS6 telephone-style handset. Clear-Com 250009 Handset Hanger for HS6.
Full Compass Systems
DIN microphone cable panel with connector and washer for the Clear-Com V-Series intercom systems. Clear-Com 115G536 DIN Mic Cable Panel for V-Series.
Full Compass Systems
DX Series Headet:HSI6000 Headset Adapter:2.5mm Headset Adapter for BP200 Beltpac and BP300 Beltpac Clear-Com CZ11453 HSI6000 2.5mm Headset Adapter.
Full Compass Systems
Power / Menu keypad for the Clear-Com FSII FreeSpeak II 2.4 GHz beltpack. Clear-Com 369G078-3 Power/Menu Keypad for FSII 2.4.
Full Compass Systems