universal condenser fan

This is a BRAND NEW A.O.Smith Universal CONDENSER FAN MOTOR. The A.O.Smith part # is F48K97A01 (also FSE1056SV1). It's 1/2 HP, 208-230v,1075 RPM.The motor is 5 5/8 in diameter (Frame 48Y). The shaft extends 6 out of the motor and is 1/2 in diameter. The rotation is reversible (just flip a wiring plug). Thanks for looking and good luck! Replaces old Part #s: Too Many to List Visit My eBay Store: NorthAmericaHVAC

This is a BRAND NEW A.O.Smith Universal CONDENSER FAN MOTOR. The A.O.Smith part # is F48K89A01 (also FSE1036SV1). It's 1/3 HP, 208-230v,1075 RPM.The motor is 5 5/8 in diameter (Frame 48Y). The shaft extends 6 out of the motor and is 1/2 in diameter. The rotation is reversible (just flip a wiring plug). Thanks for looking and good luck! Replaces old Part #s: Too Many to List Visit My eBay Store: NorthAmericaHVAC

This is a BRAND NEW A.O.Smith Universal CONDENSER FAN MOTOR. The A.O.Smith part # is F48AB18A01 (also FSE1026SV1). It's 1/4 HP, 208-230v,1075 RPM.The motor is 5 5/8 in diameter (Frame 48Y). The shaft extends 6 out of the motor and is 1/2 in diameter. Thanks for looking and good luck! Replaces old Part #s: Too Many to List Visit My eBay Store: NorthAmericaHVAC

This is a BRAND NEW Universal Condenser Motor Fan Blade. It's 14 in diameter with 2 blades/wings and a 1/2 bore for the motor shaft. It has 32 degrees pitch and Rotation (if facing air discharge side- usually looking down on an A/C unit) is Clockwise. The picture is very similiar to this blade, but may not accurately represent the pitch/diameter of the blade you will receive. Thanks for looking and good luck! Visit My eBay Store: NorthAmericaHVAC On Mar-28-12 at 19:15:11 PDT, seller added the

Thermally protected. UL recognized; CSA or ULc certified. Reversible rotation. Condenser fan motors with ball bearings. 7.5M 370V Capacitor. Electrically reversible. 60 Degree ambient temperature rating. All angle mount bearings. 1/2-1/3 Horsepower. 1075rpm. 2 Speed. 208-230 volts. 60Hz Frequency. 3.7-1.9 amps. Shaft measures 1/2 diameter by 5-1/2 length.

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 14 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 27 degrees. When facing the discharge side of the blade, the rotation would be CW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My e

Condenser Fan Motor, Permanent Split Capacitor, 1/5 to 1/2 HP, Nameplate RPM 1075, Voltage 208-230, 48 Frame, Totally Enclosed Air Over, Number of Speeds 2, Full Load Amps 3.1, Stud Mounting, Auto Thermal Protection, Insulation Class B, Service Factor 1.0, Ball Bearings, Max. Ambient Temp. 70 Degrees C, CW/CCW Rotation, Overall Length 12-7/8 In., Shaft Dia. 1/2 In., Shaft Length 6-1/2 In., Capacitor Required 2MDV7 GE Heat Shield High-Ambient PSC Condenser Fan MotorsDesign and insulation withstand higher ambient temps. throughout, to run cooler at full rated load. Quick-change rotation reversal plug. Drain plugs in each endshield. 48 leads with seal bushing. Life-Line multihorsepower models reduce inventory expense. All models are for outdoor condenser and heat pump units.UL Recognized and... Less

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 16 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 23 degrees. When facing the discharge side of the blade, the rotation would be CCW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 20 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 30 degrees. When facing the discharge side of the blade, the rotation would be CCW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My

Thermally protected. UL recognized; CSA or ULc certified. Reversible rotation. Condenser fan motor with ball bearing. 3/4 Horsepower. 1140rpm. 1 Speed. 200-230 Volts. 60Hz Frequency. 3 amps. Keyed shaft measures 5/8 diameter by 5-7/8 length. 8 Motor length.

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 12 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 33 degrees. When facing the discharge side of the blade, the rotation would be CW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My e

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 18 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 27 degrees. When facing the discharge side of the blade, the rotation would be CCW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 2 blades and is 20 in diameter with a 1/2 bore. The pitch is 28 degrees. When facing the discharge side of the blade, the rotation would be Clockwise . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My eBay Store: NorthAmericaHVAC Please contact with any questions you have, or any other parts you may need! Customer Service Home Live Chat Shipping Information Returns Disclaimer Testimonials T

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 26 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 33 degrees. When facing the discharge side of the blade, the rotation would be CCW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My

Thermally protected. UL recognized; CSA or ULc certified. DS rotation. Window A/C condenser fan and direct drive blower motor with sleeve bearing. Ideal versatility using kit 200 X brackets to accommodate various cradle base lengths. Ideal for lug mounting using lug kit 55L or 55S. 1/4-1/5-1/6 Horsepower. 1625rpm. 3 Speed. 208-230 Volts. 60Hz Frequency. 1.9-1.2-0.9 amps. Shaft measures 8-1/2 by 1/2 by 8-1/2. 4 Motor length.

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 24 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 23 degrees. When facing the discharge side of the blade, the rotation would be CW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My e

Condenser Fan Motor, Permanent Split Capacitor, 1/6 to 1/3 HP, Nameplate RPM 1075, Voltage 208-230, 48 Frame, Totally Enclosed Air Over, Number of Speeds 1, Full Load Amps 2.6, Stud Mounting, Auto Thermal Protection, Insulation Class B, Service Factor 1.0, Ball Bearings, Max. Ambient Temp. 70 Degrees C, CW/CCW Rotation, Overall Length 12-1/8 In., Shaft Dia. 1/2 In., Shaft Length 6-1/2 In., Capacitor Required 2MDV6 GE Heat Shield High-Ambient PSC Condenser Fan MotorsDesign and insulation withstand higher ambient temps. throughout, to run cooler at full rated load. Quick-change rotation reversal plug. Drain plugs in each endshield. 48 leads with seal bushing. Life-Line multihorsepower models reduce inventory expense. All models are for outdoor condenser and heat pump units.UL Recognized and... Less

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 3 blades and is 14 (measured corner to opposite corner) with an interchangable hub that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The on the blade is pitch is 27 degrees. When facing the discharge side of the blade, the rotation would be Clockwise. This fan blade is used in all brands

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 18 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 33 degrees. When facing the discharge side of the blade, the rotation would be CW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My e

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 26 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 24 degrees. When facing the discharge side of the blade, the rotation would be CCW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 2 blades and is 24 in diameter with a 1/2 bore. The pitch is 27 degrees. When facing the discharge side of the blade, the rotation would be CCW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My eBay Store: NorthAmericaHVAC Please contact with any questions you have, or any other parts you may need! Customer Service Home Live Chat Shipping Information Returns Disclaimer Testimonials Thanks!

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 12 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 23 degrees. When facing the discharge side of the blade, the rotation would be CW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My e

Thermally protected. UL recognized; CSA or ULc certified. Reversible rotation. Condenser fan motor with ball bearing. 3/4 Horsepower. 1140rpm. 1 Speed. 460 Volts. 60Hz Frequency. 1.5 amps. Keyed shaft measures 5/8 diameter by 5-7/8 length. 8 Motor length.

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 20 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 33 degrees. When facing the discharge side of the blade, the rotation would be CW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My e

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 20 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 33 degrees. When facing the discharge side of the blade, the rotation would be CCW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 2 blades and is 20 in diameter with a 1/2 bore. The pitch is 28 degrees. When facing the discharge side of the blade, the rotation would be CCW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My eBay Store: NorthAmericaHVAC Please contact with any questions you have, or any other parts you may need! Customer Service Home Live Chat Shipping Information Returns Disclaimer Testimonials Thanks!

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 24 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 18 degrees. When facing the discharge side of the blade, the rotation would be CW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My e

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 2 blades and is 18 in diameter with a 1/2 bore. The pitch is 36 degrees. When facing the discharge side of the blade, the rotation would be Clockwise . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My eBay Store: NorthAmericaHVAC Please contact with any questions you have, or any other parts you may need! Customer Service Home Live Chat Shipping Information Returns Disclaimer Testimonials T

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 2 blades and is 14 in diameter with a 1/2 bore and a 36 degree pitch. . When facing the discharge side of the blade, the rotation would be Clockwise. This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My eBay Store: NorthAmericaHVAC Please contact with any questions you have, or any other parts you may need! Customer Service Home Live Chat Shipping Information Returns Disclaimer Testimonials Tha

This is a BRAND NEW Universal Condenser Motor Fan Blade. It has 4 blades and is 22 with an interchangable hub with that allows for different hub sizes. If you cannot remove the hub off your old blade, you must purchase one for this blade. We carry 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 bore hubs in our store. The pitch is 27 degrees. When facing the discharge side of the blade, the rotation would be CCW . This fan blade is used in all brands of units. Thanks for looking and good luck!Visit My