mercury mercury mariner water pump impeller kit 6 15hp 1986 98

The AMT line of industrial/commer cial sump pump is designed for heavy duty commercial applications, as well as residential use where a combination of durability and high performance is required. Sump pump are available in stainless steel constructions with stainless steel impeller and TEFC motors in 1/2 HP for proper pump selection in most applications. Model include stainless steel shaft, screen and float. Single phase 56C frame motor is fitted with automatic switch and an 8-feet 16/3 115 VAC line cord. pump require minimum sump pit of 14-inches diameter and 24-inches depth. Carbon bearings, 29-inches to 44-inches column height, 2-inches NPT Discharge. Maximum head 30-feet. Maximum Flow 103 gpm. Semi-open, clog resistant impellers. Maximum temperature 200 degree F. Solids handling... Less

water pump upper repair kit. It includes plastic pump housing assembly, impeller, face plate, gaskets, drive key or pin, water tube guide sleeve, O rings and gearlube fill & vent screw seals. (Base not included) Fits Mercury/Mariner 65 hp (4 cylinder) through V-6 outboards with short-vane impellers and fits MerCruiser I/R/MR/Alpha drives (s/n 2495186- 0D469858).

This water pump impeller kit is designed to fit Mercury/Mariner 65 hp (4 cylinder) through V-6 outboards with short-vane impellers and MerCruiser I/R/MR/Alpha drives. It includes an impeller water tube wear plate wear plate gaskets drive shaft o-rings impeller key and housing washers/nuts.

Product Categories Anchor Boat / Motor / PWC Boat Covers Boat Fenders Cleaning Supplies Clothing Apparel Control Steering Cables Dock Mooring Electrical Electronics Instrumentation Engine Parts Fishing Fuel Tanks Systems Galley General Boating Hardware Interior Leisure Fun Stuff Lubricants Maintenance Paint Plumbing Propellers Safety Seating Trailer Ventilation Watersports Winterization Other Sporting Goods:Water Sports:Other Complete Water Pump Kit Mercury Mariner 18-3322 Complete Water Pump K

This specific marine engine manual is for the Mercury/Mariner 75 - 250 HP outboard motors spanning 1998-2002. You can see the specific horsepower models covered listed below. This manual is 632 pages and catalog number B727. MODELS COVERED MERCURY/MARINER 100 HP MERCURY/MARINER 105 JET MERCURY/MARINER 115 HP MERCURY/MARINER 115 HP OPTIMAX MERCURY/MARINER 125 JET MERCURY/MARINER 135 HP MERCURY/MARINER 135 HP OPTIMAX MERCURY/MARINER 140 JET MERCURY/MARINER 150 HP MERCURY/MARINER 150 HP OPTIMAX MERCURY/MARINER 150 MAG III MERCURY/MARINER 150 XR6 MERCURY/MARINER 175 HP MERCURY/MARINER 175 HP OPTIMAX MERCURY/MARINER 200 HP MERCURY/MARINER 200 HP OPTIMAX MERCURY/MARINER 225 HP MERCURY/MARINER 225 HP OPTIAMX MERCURY/MARINER 250 HP MERCURY/MARINER 65 JET MERCURY/MARINER 75 HP MERCURY/MARINER 80... Less

Centrifugal Pump, Power Rating 15 HP, Voltage @ 60 Hz 208-230/460 Volts, Current Rating 39.4/19.7 Amps, Impeller Diameter 6 3/8 Inches, Phase Three, Maximum Head 179 Feet, Motor Enclosure TEFC, Outlet 2 1/2 Inches, Inlet 3 Inches, Service Factor 1.15, Length 23 5/8 Inches, Height 11 1/4 Inches, Width 14 7/8 Inches, Water Flow @ 60 Feet of Head 396 GPM, Water Flow @ 70 Feet of Head 378 GPM, Water Flow @ 80 Feet of Head 364 GPM, Bronze Fitted RestrictionsNote: 1N497, 1N495, and 1N489 have a high head impeller. California Proposition 65 Warning: This product contains a chemical known to the State of California to cause cancer. Warning: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. Straight Centrifugal PumpsPumps have... Less

Mercury/Mariner 4 - 90 HP Four Stroke Outboards, 1995-2000Part #: B710Does not cover 60hp models. 560 pagesCHAPTER ONE, GENERAL INFORMATIONManual organization, Notes, cautions and warnings, Torque specifications, Engine operation, Fasteners, Lubricants, Gasket sealant, Galvanic corrosion, PropellerCHAPTER TWO, TOOLS AND TECHNIQUESSafety first, Basic hand tools, Test equipment, Service hints, Special tips, Mechanics techniquesCHAPTER THREE, TROUBLESHOOTINGTr oubleshooting test equipment, Starting difficulty, Starting system, Ignition system, Warning systems, Charging system, Fuses, Power head, Cooling system, Gearcase, Trim systemCHAPTER FOUR, LUBRICATION, MAINTENANCE AND TUNE- UPLubrication and maintenance and tune-up, Routine maintenance, Tune-up, SubmersionCHAPTER FIVE,... Less

Create impressive water features with these heavy-duty submersible pumps. Rugged direct-drive submersible pumps boast dependable, solids-handling ability. In addition, these Little Giant pumps feature a non-clogging vortex impeller and thermal overload protection with auto-reset function to help ensure years of safe and reliable pump performance. Ideally suited for water circulation in koi ponds or for driving waterfalls, streams and other water features. Constructed with stainless steel, cast iron and durable thermoplastic. 19 foot power cord. Model Max gph Max Head Inlet/Outlet Watts Dimensions 1/5 HP 2,900 21 ft NA/1-1/4 FNPT 355 7.32 x 5.21 x 12.44 high 1/3 HP 3,450 25 ft NA/1-1/2 FNPT 455 7.75 x 5.29 x 12.86 high 1/2 HP 5,000 30 ft NA/2 FNPT 590 8.8 x 5.83 x 13.85 high 3/4 HP 5,300... Less

AMT heavy duty solids handling end suction centrifugal pumps are suited for liquid and chemical transfer, heating and cooling, recirculation, booster service, dirty water and other industrial applications. Stainless steel units are especially effective in applications where rust and/or corrosion can develop in systems. Semi-open impeller features self-cleaning ability that makes the unit useful in applications involving up to 1/8-inches diameter solids and muddy or dirty liquids, as well as clean, clear fluids. Discharge position can be adjusted in 90 degree increments with vent and drain plugs for all positions. Type 21 mechanical seal and O-ring casing seal. Pumps are close coupled to totally enclosed fan cooled (TEFC) motors. Pumps are not self-priming and require flooded suction. Cast... Less

AMT heavy duty solids handling end suction centrifugal pumps are suited for liquid and chemical transfer, heating and cooling, recirculation, booster service, dirty water and other industrial applications. Stainless steel units are especially effective in applications where rust and/or corrosion can develop in systems. Semi-open impeller features self-cleaning ability that makes the unit useful in applications involving up to 1/8-inches diameter solids and muddy or dirty liquids, as well as clean, clear fluids. Discharge position can be adjusted in 90 degree increments with vent and drain plugs for all positions. Type 21 mechanical seal and O-ring casing seal. Pumps are close coupled to totally enclosed fan cooled (TEFC) motors. Pumps are not self-priming and require flooded suction. Cast... Less

Centrifugal Pump, Power Rating 15 HP, Voltage @ 60 hz 208-230/460 Volts, Current Rating 41/20.5 Amperes, Impeller Diameter 7 5/8 Inches, Phase Three, Maximum Head 260 Feet, Motor Enclosure ODP, Outlet 1 1/2 Inches, Inlet 2 Inches, Service Factor 1.15, Length 23 5/8 Inches, Height 10 3/4 Inches, Width 14 9/16 Inches, Water Flow @ 160 Feet of Head 250 Gallons per Minute, Water Flow @ 180 Feet of Head 230 Gallons per Minute, Water Flow @ 200 Feet of Head 210 Gallons per Minute, Bronze Fitted RestrictionsNote: 1N497, 1N495, and 1N489 have a high head impeller. California Proposition 65 Warning: This product contains a chemical known to the State of California to cause cancer. Warning: This product contains a chemical known to the State of California to cause birth defects or other... Less

AMT heavy duty solids handling end suction centrifugal pumps are suited for liquid and chemical transfer, heating and cooling, recirculation, booster service, dirty water and other industrial applications. Stainless steel units are especially effective in applications where rust and/or corrosion can develop in systems. Semi-open impeller features self-cleaning ability that makes the unit useful in applications involving up to 1/8-inches diameter solids and muddy or dirty liquids, as well as clean, clear fluids. Discharge position can be adjusted in 90 degree increments with vent and drain plugs for all positions. Type 21 mechanical seal and O-ring casing seal. Pumps are close coupled to totally enclosed fan cooled (TEFC) motors. Pumps are not self-priming and require flooded suction. Cast... Less

Pump, Vertical, 1/6 HP, Motor Enclosure TEFC, Amps AC 2.8, Housing PVDF, Impeller Material PVDF, NPT Inlet (In.) 3/4 F, NPT Outlet (In.) 1/2 M, GPM of Water @ 15 Ft. of Head 9, Max. Head 19.5 Ft., Max. Dia. Solids 1/16 In., Max. Liquid Temp. 240 F, For Use With Corrosives CPVC and PVDF Vertical PumpsCorrosion- resistant nonmetallic construction eliminates metal contact with pumped fluids, and related contamination and corrosive reactions. Twin-impeller design minimizes entrained air and maintains a dynamic seal, while the close-coupled design eliminates need for additional couplings and motor alignment. Fume barrier helps keep corrosive vapors from escaping into the atmosphere or damaging motors. Oversized, double-sealed ball bearings. 115V motors are supplied with manual On/Off switch... Less

AMT high head end suction centrifugal pumps are designed for continuous-duty OEM, Industrial/Commer cial and processing applications including circulation, chemical processing, liquid transfer, heating and cooling, sprinkler/fire protection systems and pressure boosting. These heavy duty high pressure pumps are available in a variety of construction and seal materials to meet your specification. Pull-from-rear design for easy servicing without disturbing any piping. High efficiency closed impeller maximizes performance. Pumps are close coupled to Totally Enclosed Fan Cooled (TEFC) motors. Pumps are not self-priming and require flooded suction. Cast stainless steel construction with Viton seals. Optional silicon carbide mechanical seals available. Discharge port rotates in 90 degree... Less

AMT solids handling end suction centrifugal pumps are designed for continuous-duty low pressure OEM, Industrial/Commer cial and general service applications including circulation, chemical processing, liquid transfer, dirty water and cooling. Pull-from-rear design for easy service without disturbing any piping. Self-cleaning semi-open impeller prevents clogging and handles solids of 1/8-inches diameter. Pumps are close coupled to Totally Enclosed Fan Cooled (TEFC) motors. Pumps are not self-priming and require flooded suction. Cast stainless steel construction with viton seal. Measures 13-1/2-inches length by 8-51/64-inches width by 8-19/32-inches height.

Pump, Vertical, 1/4 HP, Motor Enclosure TEFC, Amps AC 1, Housing CPVC, Impeller Material CPVC, NPT Inlet (In.) 3/4 F, NPT Outlet (In.) 1/2 M, GPM of Water @ 15 Ft. of Head 14, Max. Head 21 Ft., Max. Dia. Solids 1/16 In., Max. Liquid Temp. 180 F, For Use With Corrosives CPVC and PVDF Vertical PumpsCorrosion- resistant nonmetallic construction eliminates metal contact with pumped fluids, and related contamination and corrosive reactions. Twin-impeller design minimizes entrained air and maintains a dynamic seal, while the close-coupled design eliminates need for additional couplings and motor alignment. Fume barrier helps keep corrosive vapors from escaping into the atmosphere or damaging motors. Oversized, double-sealed ball bearings. 115V motors are supplied with manual On/Off switch and... Less

The AMT line of industrial/commer cial sump pump is designed for heavy duty commercial applications, as well as residential use where a combination of durability and high performance is required. Sump pump are available in stainless steel construction with stainless steel impeller and TEFC motors in 1/2 HP for proper pump selection in most applications. Model include stainless steel shaft, screen and float. Single phase 56C frame motor is fitted with automatic switch and an 8-feet 16/3 115 VAC line cord. pump require minimum sump pit of 14-inches diameter and 24-inches depth. Carbon bearings, 29-inches to 44-inches column height, 2-inches NPT Discharge. Maximum head 30-feet. Maximum Flow 103 gpm. Semi-open, clog resistant impellers. Maximum temperature 200 degree F. Solids handling design... Less

Circulator Pump, Closed Loop System, 1/15 HP, 1 Phase, Voltage 115, 1.1 Amps, Inlet/Outlet Flanged, Housing Material Bronze, Max. Temp. 225 F, Max. Working Pressure 150 PSI, Shut-Off 18.5 Ft., 2950 RPM, Impeller Material Noryl, Thermal Protection, Additional Features Three Speed Motor, Maintenance Free, Wet-Rotor, Warranty Length 3 Years RestrictionsCalif ornia Proposition 65 Warning: This product contains a chemical known to the State of California to cause cancer. Warning: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. Hot Water Circulating Pumps1-phase models are thermally protected Cast-iron units are not for potable waterWet Rotor, Maintenance- FreeDuraGlide bearing system helps provide high starting torque for... Less