Drill Bits

Also known as: ATD-277, ATD277; High carbon steel for durability and precision threading 34 plug tap sizes are perfect for general purpose threading 34 hexagon die sizes are ideal for general maintenance and repair work Hexagon dies allow a socket or wrench to be used in areas with limited space 36 high speed steel drill bits with drill to tap size interchange chart 5 spiral flute screw & bolt extractors

The YG-1 G8A37 TiAlN-coated carbide stub cut-length corner radius end mill has a long-reach shank, four flutes, and a center-cutting design for high-performance slotting and machining in recessed areas on hardened steel, heat-resistant steel, and other materials with a Rockwell hardness up to C70. Corner radius end mills have a square end with rounded corners to reduce chipping and extend the life of the tool. The stub-length cutting edges increase tool strength and make it less likely to break in the material being machined. It is best used when depth of cut is shallow. The long-reach shank provides greater access to recessed areas of the workpiece than tools with a standard shank length. (Feed should be reduced by around 50%.) Four flutes produce a better finish than fewer flutes. The... Less

Ideal for drilling graphite and other nonmetals such as composites, green ceramics, carbon fiber, PVC, acrylic, ABS, nylon, PTFE, and fiberglass. These drill bits have a 118 degree self-centering, four-facet point for good cutting edge rigidity and vibration damping. The shank diameter is the same as the drill bit size.

The ultimate in durability and sharpness, the titanium-coated bit from Task Tools offers fast drilling in steel, wood, plastic and more time and time again. High Speed Steel construction makes this bit stand up to wear and tear in any material. A 135-Degree, split point design lets the bit find purchase and begin cutting on contact with no walking or scratching the work piece. The bit is also precision-ground for smooth drilling operations. Bit sizes: 1/16- through 1/2-Inch bits .

The YG-1 G8A37 TiAlN-coated carbide stub cut-length corner radius end mill has a long-reach shank, four flutes, and a center-cutting design for high-performance slotting and machining in recessed areas on hardened steel, heat-resistant steel, and other materials with a Rockwell hardness up to C70. Corner radius end mills have a square end with rounded corners to reduce chipping and extend the life of the tool. The stub-length cutting edges increase tool strength and make it less likely to break in the material being machined. It is best used when depth of cut is shallow. The long-reach shank provides greater access to recessed areas of the workpiece than tools with a standard shank length. (Feed should be reduced by around 50%.) Four flutes produce a better finish than fewer flutes. The... Less

The YG-1 G8A37 TiAlN-coated carbide stub cut-length corner radius end mill has a long-reach shank, four flutes, and a center-cutting design for high-performance slotting and machining in recessed areas on hardened steel, heat-resistant steel, and other materials with a Rockwell hardness up to C70. Corner radius end mills have a square end with rounded corners to reduce chipping and extend the life of the tool. The stub-length cutting edges increase tool strength and make it less likely to break in the material being machined. It is best used when depth of cut is shallow. The long-reach shank provides greater access to recessed areas of the workpiece than tools with a standard shank length. (Feed should be reduced by around 50%.) Four flutes produce a better finish than fewer flutes. The... Less

High quality silver and deming drill bits set with HSS material construction, finished in black and gold color. 1/2-inch shank with Tri-flat shank for sure grip. 135 degree with split point design for fast penetration and accuracy. Set complets with a aluminum tool box case. Sizes includes: 1/2, 33/64, 17/32, 35/64, 9/16, 37/64, 19/32, 39/64, 5/8, 41/64, 21/32, 43/64, 11/16, 45/64, 23/32, 47/64, 3/4, 49/64, 25/32, 51/64, 13/16, 53/64, 27/32, 55/64, 7/8, 57/64, 29/32, 59/64, 15/16, 61/64, 31/32, 63/64 & 1

The YG-1 EMB12 AlTiN-coated carbide square nose end mill has a variable helix, four flutes, and a center-cutting design for high-performance machining on alloy steel, cast iron, stainless steel, titanium, nickel-based alloys, and most materials with a Rockwell hardness less than C40. Variable-helix end mills combine varying helix angles with unequal flute spacing to reduce harmful vibration between the tool and the workpiece, improve surface finish, and provide higher cutting capacity and material-removal rates compared to conventional end mills. Four flutes produce a better finish than fewer flutes. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. The AlTiN... Less

The YG-1 EMB12 AlTiN-coated carbide square nose end mill has a variable helix, four flutes, and a center-cutting design for high-performance machining on alloy steel, cast iron, stainless steel, titanium, nickel-based alloys, and most materials with a Rockwell hardness less than C40. Variable-helix end mills combine varying helix angles with unequal flute spacing to reduce harmful vibration between the tool and the workpiece, improve surface finish, and provide higher cutting capacity and material-removal rates compared to conventional end mills. Four flutes produce a better finish than fewer flutes. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. The AlTiN... Less

1.00M-13.00M SET

The Niagara Cutter A208 uncoated (bright) high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has... Less

Set Contains: Drip Rail Dolly Length: 9.1/2(240mm) Weight: 880gm Utility Dolly Length: 2.3/4(70mm) Weight: 960gm Double End Hand Dolly Length: 2.3/4(70mm) Weight: 840gm Double End Hand Dolly Length: 6.3/4(175mm) Weight: 1580gm Curved Dolly Length: 5.1/2(140mm) Weight: 940gm Toe Dolly Length: 4.3/4(120mm) Weight: 620gm Heel Dolly Length: 2.1/2(65mm) Weight: 360gm

The Niagara Cutter HMC630 TiCN-coated high-speed steel square nose end mill has a larger diameter than conventional end mills, four flutes, a 37-degree helix angle, and is designed for machining aluminum and nonferrous materials. The large-diameter shank provides extra strength and rigidity. The four large flutes produce a better finish than fewer flutes. The 37-degree helix angle provides a higher cutting action than a standard 30-degree helix to help avoid material build-up on the cutting edges and flutes. It also provides more support behind the cutting edge than higher angles. The TiCN coating lubricates the end mill for high-temperature stability, and offers increased hardness and greater abrasion resistance than uncoated or TiN-coated tools. High-speed steel (HSS) is a common,... Less

The Niagara Cutter A208 uncoated (bright) high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has... Less

The Niagara Cutter A208 uncoated (bright) high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has... Less

The Niagara Cutter A208 TiCN-coated high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. The TiCN coating lubricates the end mill for high-temperature stability, and offers increased hardness and greater abrasion resistance than uncoated tools. High-speed steel (HSS) is a common general-purpose steel... Less

The Niagara Cutter AB910 uncoated high-speed steel ball nose end mill has two flutes and a 37-degree helix for milling aluminum and other nonferrous materials. The 37-degree helix angle provides more support behind the cutting edge than higher angles and increases cutting action and chip evacuation compared to the standard 30-degree helix. It efficiently cuts aluminum and other nonferrous materials, moving it up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common, general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s... Less

The Niagara Cutter AB910 uncoated high-speed steel ball nose end mill has two flutes and a 37-degree helix for milling aluminum and other nonferrous materials. The 37-degree helix angle provides more support behind the cutting edge than higher angles and increases cutting action and chip evacuation compared to the standard 30-degree helix. It efficiently cuts aluminum and other nonferrous materials, moving it up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common, general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s... Less

The Niagara Cutter HMC630 TiCN-coated high-speed steel square nose end mill has a larger diameter than conventional end mills, four flutes, a 37-degree helix angle, and is designed for machining aluminum and nonferrous materials. The large-diameter shank provides extra strength and rigidity. The four large flutes produce a better finish than fewer flutes. The 37-degree helix angle provides a higher cutting action than a standard 30-degree helix to help avoid material build-up on the cutting edges and flutes. It also provides more support behind the cutting edge than higher angles. The TiCN coating lubricates the end mill for high-temperature stability, and offers increased hardness and greater abrasion resistance than uncoated or TiN-coated tools. High-speed steel (HSS) is a common,... Less

This excellent Cordless Drill Set has nearly everything you need for almost any job all in one convenient durable carrying case! You wont be caught off guard on any project with all the bits, sockets and drivers provided in this kit. The bits coupled with the powerful 18V drill and flashlight will allow you to complete nearly any project.Features include:ONE BATTERY1300 mAh NiCd batteryForward / ReverseKeyless chuck: 0.8-10mmTorque stage: 16+1No-load speed: 0-550 rpmSoft gripConvenient and durable carrying caseBattery charger and AC adapterSlot driver bits (9): 3mm, 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 6.5mm, 7mm, 8mmPhillips driver bits (8): PH0, PH1, PH2, PH3, PZ0, PZ1, PZ2, PZ3Hex driver bits (8): H2, H2.5, H3, H3.5, H4, H5, H6, H8Sockets (18): 5mm (2), 6mm (2), 7mm (2), 8mm (2), 9mm (2), 10mm... Less

The Dormer R457 series short length drill bit is made from solid carbide with a TiAlN coating and has a 140-degree split point for increased rigidity in heavy feed-rate drilling applications on ferrous materials, high-temperature alloys, and titanium. Solid carbide is harder than high-speed or cobalt steel, provides longer tool life at higher speeds, and produces close-tolerance holes in hard materials. The titanium aluminum nitride (TiAlN) coating provides wear and corrosion resistance in high-speed or heavy feed-rate drilling. A self-centering 140-degree split point penetrates hard material without a pilot hole, and produces smaller chips that reduce clogging compared to a 118-degree point. The drill bit has internal channels that guide coolant through the body to the drill bit tip for... Less

The Niagara Cutter A208 TiCN-coated high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. The TiCN coating lubricates the end mill for high-temperature stability, and offers increased hardness and greater abrasion resistance than uncoated tools. High-speed steel (HSS) is a common general-purpose steel... Less

The Niagara Cutter A208 uncoated (bright) high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has... Less

The Niagara Cutter A208 uncoated (bright) high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has... Less

The Niagara Cutter A208 uncoated (bright) high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has... Less

The Niagara Cutter AB910 uncoated high-speed steel ball nose end mill has two flutes and a 37-degree helix for milling aluminum and other nonferrous materials. The 37-degree helix angle provides more support behind the cutting edge than higher angles and increases cutting action and chip evacuation compared to the standard 30-degree helix. It efficiently cuts aluminum and other nonferrous materials, moving it up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common, general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s... Less

The Niagara Cutter A208 TiCN-coated high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. The TiCN coating lubricates the end mill for high-temperature stability, and offers increased hardness and greater abrasion resistance than uncoated tools. High-speed steel (HSS) is a common general-purpose steel... Less

The Niagara Cutter A208 uncoated (bright) high-speed steel square nose end mill has two flutes and a 37-degree helix angle for profiling and slotting applications on aluminum and other nonferrous materials. The 37-degree helix offers increased cutting action compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. High-speed steel (HSS) is a common general-purpose steel for cutting tools; this tool has no coating or surface treatment. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has... Less