Category

Tools and Accessories
Showing results for "Voos Da Tap"
Results 1 - 40 of 1500+

Micro Tap Guide

$12.95
Brownells Micro Tap Guide
+ $7.95 shipping
/micro-tap-guide/lqFTunJOboeZqT76SBlmpQ==/info
Brownells
IN_STOCK ( In stock )
Store not rated
Applies just enough pressure on the tap for precise centering and perfectly square threads. Just install in your lathe tailstock, drill press, or mill spindle, and align the point of the tap guide with the small hole at the end of the tap wrench. Adjust the tailstock or travel to remove all free-play between guide, tap wrench with installed tap, and pre-drilled hole. As you cut the threads by hand, the tap guide's internal spring keeps steady pressure on the tap to prevent misalignment or jumping the threads. Fully adjustable spring tension allows fine-tuning the amount of pressure on the tap. Knurled bottleneck provides a non-slip grasp. Reversible guide tip fits male or female tap wr Mfg: Fisher Machine Shop, Inc. SPECS: Steel, hardened, knurled bottleneck. 31/8 (7.9cm) OAL, ½ (13mm)... Less
More

Single Port Coax Tap - 5 To...

$2.09
ShowMeCables Single Port Coax Tap - 5 To 1000 Mhz - 9db
+ $3.99 shipping
/single-port-coax-tap-5/GebSRrYoxdxOReRFgvVfSQ==/info
ShowMeCables
IN_STOCK ( In stock )
Store not rated
Coax taps are used when one source needs to feed multiple devices in the same location. This signal port coax tap has one feed through port and a one tap port. The feed through port typically will go to the next coax tap in the line. The tap port will be used for the device. Features: 75 Ohm Tap Value: 9dB Frequency Range: 5-1000MHz Tap Loss: 9 +/- 1.5dB Insertion Loss: 2.2dB Isolation out to tap: 20dB Return Loss: 15dB All Ports F-type Female A/V & PC Equipment > Satellite / Antenna Hardware > Taps, A/V & PC Equipment > Satellite / Antenna Hardware > Taps 240
More

Drum Tap w/ Gasket & Nut

$5.75
Beverage Factory.com Drum Tap w/ Gasket & Nut
+ $7.00 shipping
/drum-tap-w-gasket-nut/-N5WjzRmmWT8SmQbWi-2cQ==/info
Beverage Factory.com
IN_STOCK ( In stock )
This easy-to-use Drum Tap is a great way to turn any fermenting bucket into a home brew bottling bucket. It is compatible with our 6.5 and 7.8 gallon pre-drilled buckets, or any bucket with a 1 diameter hole drilled into it. It's round screw shut-off works in much the same way as outdoor faucet, making it easy to control the on and off flow of your beer or wine. Includes a gasket and nut to secure it to your bucket.
More

Posi-Tap Mini Assortment ...

$8.99
Crutchfield Posi-Tap Mini Assortment Posi-Tap Reduced Size 6 pc Assortment
+ $6.99 shipping
/positap-mini-assortment/sv-oDO8be6OQ3ui8BXnVgQ==/info
Crutchfield
IN_STOCK ( In stock )
Posi-Tap Reduced Size 6 pc Assortment tap into 18- to 26-gauge wires without cutting or stripping them,asssortment of hand-tightened connectors for stranded wire,no crimping, soldering, or taping
More

Wisdom 40 Piece Tap and Die...

$21.99
MidwayUSA Wisdom 40 Piece Tap and Die Set Metric
+ $7.79 shipping
/wisdom-40-piece-tap-and/E7LninoIR4aiPmW_gDhPUw==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
This carbon steel tap and die set contains taps and dies in a variety of thread patterns. Includes the following Metric thread sizes: 3 x 0.5mm, 3 x 0.6mm, 4 x 0.7mm, 4 x 0.75mm, 5 x 0.8mm, 5 x 0.9mm, 6 x 0.75mm, 6 x 1.0mm, 7 x 0.75mm, 8 x 1.0mm, 8 x 1.25mm, 10 x 1.25mm, 10 x 1.5mm, 12 x 1.5mm, 12 x 1.75mm Also includes: 1/8 NPT x 27 tap wrench, T-handle wrench, die handle, screwdriver, screw pitch gauge and carrying case. Technical InformationMateri al: Carbon Steel Tools Included: Taps and Dies in the following thread patterns: 3-0.5 mm, 3-0.6 mm, 4-0.7 mm, 4-0.75 mm, 5-0.8 mm, 5-0.9 mm, 6-0.75 mm, 6-1.0 mm, 7-0.75 mm, 8-1.0 mm, 8-1.25 mm, 10-1.25 mm, 10-1.5 mm, 12-1.5 mm, 12-1.75 mm, 1/8 NPT-27 Long Handle Adjustable Tap Wrench T-Handle Tap Wrench Die Handle Screwdriver Screw Pitch... Less
More

Single Port Coax Tap - 5 To...

$1.99
ShowMeCables Single Port Coax Tap - 5 To 1000 Mhz - 6db
+ $3.99 shipping
/single-port-coax-tap-5/fsHF3SCEDqVCtZ-H2JwOqQ==/info
ShowMeCables
IN_STOCK ( In stock )
Store not rated
Coax taps are used when one source needs to feed multiple devices in the same location. This signal port coax tap has one feed through port and a one tap port. The feed through port typically will go to the next coax tap in the line. The tap port will be used for the device. Features: 75 Ohm Tap Value: 6dB Frequency Range: 5-1000MHz Tap Loss: 6 +/- 1.5dB Insertion Loss: 2.6dB Isolation out to tap: 20dB Return Loss: 15dB All Ports F-type Female A/V & PC Equipment > Satellite / Antenna Hardware > Taps, A/V & PC Equipment > Satellite / Antenna Hardware > Taps 3240
More

Tap Wrenches - Tap Wrench...

$16.99
Brownells Tap Wrenches - Tap Wrench Wrench No. 1, 9 1/4'''' Long, Fits 0 To 1/2''''
+ $7.95 shipping
/tap-wrenches-tap-wrench/YlAaZ_i7vlWGkjMb3rscwA==/info
Brownells
IN_STOCK ( In stock )
Store not rated
No. 1, 9-¼ long, fits 0 to ½ taps with square shank measuring up to .332 across the flats. No. 2, 18, fits ¼ to 1 taps with square shank measuring up to .655 across the flats. Mfg: Irwin Industrial Tool Co.
More

Instant Tap Connectors with...

$2.08
Deep Surplus Instant Tap Connectors with Stop for 18-14 Wire- Blue (Bag of 25)
No Shipping Info
/instant-tap-connectors/rMyh1jhJiCFEo0F-x8rbew==/info
Deep Surplus
IN_STOCK ( In stock )
Comes in bags of 25 each.
More

GGS_13098 Side Can Tap,...

$12.86
Walmart.com GGS_13098 Side Can Tap, Manual, Green
+ $5.00 shipping
/ggs13098-side-can-tap/_W9H1v37AENRiB_V3Vyv-A==/info
Walmart.com
IN_STOCK ( In stock )
Side Can Tap, Color Green, 7-1/2 In. Length, Width 5-1/2 In., HVAC Refrigerant Cans, For Use With Disposable Refrigerant Cylinders, Includes 1/4 In. SAE, 1/2 In. ACME Ports With Valves, (2) Adaptors Features Application : HVAC Refrigerant Cans Color : Green For Use With : Disposable Refrigerant Cylinders Includes : 1/4 SAE, 1/2 ACME Ports With Valves, (2) Adaptors Item : Side Can Tap Length : 7-1/2 Package Quantity : 1 Size : Hand Held Type : Manual Width (In.) : 5-1/2 Fits : Disposable Refrigerant Cylinders Characteristics : Hand Held Width : 5-1/2
More

Single Port Coax Tap - 5 To...

$2.09
ShowMeCables Single Port Coax Tap - 5 To 1000 Mhz - 16db
+ $3.99 shipping
/single-port-coax-tap-5/5RV0OlIeMPEKHtUbA3KFfw==/info
ShowMeCables
IN_STOCK ( In stock )
Store not rated
Coax taps are used when one source needs to feed multiple devices in the same location. This signal port coax tap has one feed through port and a one tap port. The feed through port typically will go to the next coax tap in the line. The tap port will be used for the device. Features: 75 Ohm Tap Value: 16dB Frequency Range: 5-1000MHz Tap Loss: 16 +/- 1.5dB Insertion Loss: 1.2dB Isolation out to tap: 24dB Return Loss: 15dB All Ports F-type Female A/V & PC Equipment > Satellite / Antenna Hardware > Taps, A/V & PC Equipment > Satellite / Antenna Hardware > Taps SKY2340-16
More

Wisdom 40 Piece Tap and Die...

$21.99
MidwayUSA Wisdom 40 Piece Tap and Die Set SAE
+ $7.79 shipping
/wisdom-40-piece-tap-and/cKtF_5jrvJMfCUYamupZnw==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
This carbon steel tap and die set contains taps and dies in a variety of thread patterns. Includes the following SAE thread sizes: 4 x 40, 6 x 32, 8 x 32, 10 x 32, 10 x 24, 12 x 24, 1/4 x 20, 1/4 x 28, 5/16 x 18, 5/16 x 24, 3/8 x 16, 3/8 x 24, 7/16 x 14, 7/16 x 20, 1/2 x 13, 1/2 x 20, 1/8NPT x 27 Also includes: 1/8 NPT x 27 tap wrench, T-handle wrench, die handle, screwdriver, screw pitch gauge and carrying case.
More

''''perfect Cut'''' Premium...

$25.99
Brownells ''''perfect Cut'''' Premium Tap - 8-40 Bottom Three-Flute Tap
+ $7.95 shipping
/perfect-cut/-7wpljODu4x2FSVdfCivVw==/info
Brownells
IN_STOCK ( In stock )
Store not rated
Not magic, just perfect! When we first tried these taps (recommended by customer Dan Baldwin), we thought they were extra hard, coated or treated somehow . . . they're that much better than any tap we've ever used before. But, the U.S. company that's been making them since 1912 says the secret is plain old care and quality control. The ground threads are held to incredibly tight tolerances for roundness, thread spacing, etc. Result is, all the teeth cut equally so the whole tapping process goes faster, the taps last longer, breakage is cut way down and the threads are the finest you'll ever see. Try them; you'll tap more holes per tap than you thought possible! Premi Mfg: Reiff & Nestor Company SPECS: H-2, High Speed tool steel.
More

Single Port Coax Tap - 5 To...

$2.09
ShowMeCables Single Port Coax Tap - 5 To 1000 Mhz - 20db
+ $3.99 shipping
/single-port-coax-tap-5/lq0CO8itwi-FxmqKQNsVnw==/info
ShowMeCables
IN_STOCK ( In stock )
Store not rated
Coax taps are used when one source needs to feed multiple devices in the same location. This signal port coax tap has one feed through port and a one tap port. The feed through port typically will go to the next coax tap in the line. The tap port will be used for the device. Features: 75 Ohm Tap Value: 20dB Frequency Range: 5-1000MHz Tap Loss: 20 +/- 1.5dB Insertion Loss: 1.2dB Isolation out to tap: 28dB Return Loss: 15dB All Ports F-type Female A/V & PC Equipment > Satellite / Antenna Hardware > Taps, A/V & PC Equipment > Satellite / Antenna Hardware > Taps SKY2340-20
More

''''perfect Cut'''' Premium...

$16.99
Brownells ''''perfect Cut'''' Premium Tap - 6-48 Bottom Three-Flute Tap
+ $7.95 shipping
/perfect-cut/-jGLdVshWPb8pyDz_0dYBw==/info
Brownells
IN_STOCK ( In stock )
Store not rated
Not magic, just perfect! When we first tried these taps (recommended by customer Dan Baldwin), we thought they were extra hard, coated or treated somehow . . . they're that much better than any tap we've ever used before. But, the U.S. company that's been making them since 1912 says the secret is plain old care and quality control. The ground threads are held to incredibly tight tolerances for roundness, thread spacing, etc. Result is, all the teeth cut equally so the whole tapping process goes faster, the taps last longer, breakage is cut way down and the threads are the finest you'll ever see. Try them; you'll tap more holes per tap than you thought possible! Premi Mfg: Reiff & Nestor Company SPECS: H-2, High Speed tool steel.
More

10-10386-3 Erickson Da Series...

$8.95
eBay 10-10386-3 Erickson Da Series Double-angle Solid Tap Collets - M3 & M4
+ $7.25 shipping
/10103863-erickson-da/8AQ6zCIc4olPdTjlpOxJVw==/info
eBay
IN_STOCK ( In stock )
10-10386-3 Erickson DA Series Double-Angle Solid Tap Collets - M3 M4 (Pkg of 4) New UnusedDouble Angle Solid Tap Collet for M3 M4 Tap Sizes Provides positive retention for tapping applications. Design of slots in back of collet acts as a drive for the tap square.Can be used in all standard J-series double-angle collet chucks.Industry- standard Erickson double-angle collet system Body Diameter Max (in): 0.5390 Body Diameter Max (mm): 13.691 Collet Series: J Overall Length (in): 1.1875 Overall Le
More

Posi-Tap PTA1218M Posi-Tap...

$8.99
Crutchfield Posi-Tap PTA1218M Posi-Tap Reduced Size 12-18 ga 6 pc
+ $6.99 shipping
/positap-pta1218m/9XDLjJOPUVh0t3p0QKN2Cw==/info
Crutchfield
IN_STOCK ( In stock )
Posi-Tap Reduced Size 12-18 ga 6 pc tap into 12- to 18-gauge wires without cutting or stripping them,hand-tightene d connectors for stranded wire,no crimping, soldering, or taping
More

Instant Tap Connectors with...

$2.08
Deep Surplus Instant Tap Connectors with Stop for 22-18 Wire- Red (Bag of 25)
No Shipping Info
/instant-tap-connectors/RYV2f9oOUj04tXkosyyZ2w==/info
Deep Surplus
IN_STOCK ( In stock )
Comes in bags of 25 each.
More

''''perfect Cut'''' Premium...

$17.50
Brownells ''''perfect Cut'''' Premium Tap - 6-48 Plug Three-Flute Tap
+ $7.95 shipping
/perfect-cut/YEu0tgskxdgU66B8yoKdTA==/info
Brownells
IN_STOCK ( In stock )
Store not rated
Not magic, just perfect! When we first tried these taps (recommended by customer Dan Baldwin), we thought they were extra hard, coated or treated somehow . . . they're that much better than any tap we've ever used before. But, the U.S. company that's been making them since 1912 says the secret is plain old care and quality control. The ground threads are held to incredibly tight tolerances for roundness, thread spacing, etc. Result is, all the teeth cut equally so the whole tapping process goes faster, the taps last longer, breakage is cut way down and the threads are the finest you'll ever see. Try them; you'll tap more holes per tap than you thought possible! Premi Mfg: Reiff & Nestor Company SPECS: H-2, High Speed tool steel.
More

''''perfect Cut'''' Premium...

$8.25
Brownells ''''perfect Cut'''' Premium Tap - 6-40 Plug Three-Flute Tap
+ $7.95 shipping
/perfect-cut/hoyxgk0kQYP-bZ_kDFg-2A==/info
Brownells
IN_STOCK ( In stock )
Store not rated
Not magic, just perfect! When we first tried these taps (recommended by customer Dan Baldwin), we thought they were extra hard, coated or treated somehow . . . they're that much better than any tap we've ever used before. But, the U.S. company that's been making them since 1912 says the secret is plain old care and quality control. The ground threads are held to incredibly tight tolerances for roundness, thread spacing, etc. Result is, all the teeth cut equally so the whole tapping process goes faster, the taps last longer, breakage is cut way down and the threads are the finest you'll ever see. Try them; you'll tap more holes per tap than you thought possible! Premi Mfg: Reiff & Nestor Company SPECS: H-2, High Speed tool steel.
More

''''perfect Cut'''' Premium...

$22.99
Brownells ''''perfect Cut'''' Premium Tap - 8-40 Plug Three-Flute Tap
+ $7.95 shipping
/perfect-cut/llxRGxQsRqIGUD5o115m9w==/info
Brownells
IN_STOCK ( In stock )
Store not rated
Not magic, just perfect! When we first tried these taps (recommended by customer Dan Baldwin), we thought they were extra hard, coated or treated somehow . . . they're that much better than any tap we've ever used before. But, the U.S. company that's been making them since 1912 says the secret is plain old care and quality control. The ground threads are held to incredibly tight tolerances for roundness, thread spacing, etc. Result is, all the teeth cut equally so the whole tapping process goes faster, the taps last longer, breakage is cut way down and the threads are the finest you'll ever see. Try them; you'll tap more holes per tap than you thought possible! Premi Mfg: Reiff & Nestor Company SPECS: H-2, High Speed tool steel.
More

Posi-Products Connector Kit ...

$8.99
Crutchfield Posi-Products Connector Kit 6 pieces Posi-Tap 16-18 Gauge
+ $6.99 shipping
/posiproducts-connector/PVkXsRWKVIf_QpEOfOIK3Q==/info
Crutchfield
IN_STOCK ( In stock )
6 pieces Posi-Tap 16-18 Gauge tap into 16- to 18-gauge wires without cutting or stripping them,hand-tightene d connectors for stranded wire,no crimping, soldering, or taping
More

Instant Tap Connectors with...

$4.40
Deep Surplus Instant Tap Connectors with Stop for 12-10 Wire- Yellow (Bag of 25)
No Shipping Info
/instant-tap-connectors/U2XXJfFb-hGKrrC4NiGxbA==/info
Deep Surplus
IN_STOCK ( In stock )
Comes in bags of 25 each.
More

''''perfect Cut'''' Premium...

$8.25
Brownells ''''perfect Cut'''' Premium Tap - 6-40 Bottom Three-Flute Tap
+ $7.95 shipping
/perfect-cut/zSBds3xfSoY7oPKqIPYyyQ==/info
Brownells
IN_STOCK ( In stock )
Store not rated
Not magic, just perfect! When we first tried these taps (recommended by customer Dan Baldwin), we thought they were extra hard, coated or treated somehow . . . they're that much better than any tap we've ever used before. But, the U.S. company that's been making them since 1912 says the secret is plain old care and quality control. The ground threads are held to incredibly tight tolerances for roundness, thread spacing, etc. Result is, all the teeth cut equally so the whole tapping process goes faster, the taps last longer, breakage is cut way down and the threads are the finest you'll ever see. Try them; you'll tap more holes per tap than you thought possible! Premi Mfg: Reiff & Nestor Company SPECS: H-2, High Speed tool steel.
More

Posi-Products Connector Kit ...

$8.99
Crutchfield Posi-Products Connector Kit 6 pieces Posi-Tap Assortment
+ $6.99 shipping
/posiproducts-connector/QkyWY6jgRwsrn1ruJm99MA==/info
Crutchfield
IN_STOCK ( In stock )
6 pieces Posi-Tap Assortment tap into 10- to 22-gauge wires without cutting or stripping them,hand-tightene d connectors for stranded wire,no crimping, soldering, or taping
More

Posi-Tap PTA2022M Posi-Tap...

$8.99
Crutchfield Posi-Tap PTA2022M Posi-Tap Reduced Size 20-22 ga 6 pc
+ $6.99 shipping
/positap-pta2022m/-nVzr6NMehHNPHMJusyUzA==/info
Crutchfield
IN_STOCK ( In stock )
Posi-Tap Reduced Size 20-22 ga 6 pc tap into 20- to 22-gauge wires without cutting or stripping them,hand-tightene d connectors for stranded wire,no crimping, soldering, or taping
More

Tms Size 1 Da200 Collet Type...

$49.99
eBay Tms Size 1 Da200 Collet Type Tap Adapter Bilz
+ $7.50 shipping
/tms-size-1-da200-collet/-83Yw5lZMXkG_SvxTjr3ZA==/info
eBay
IN_STOCK ( In stock )
TMS DA200 COLLET TAP ADAPTER PART NO. 51-701-094 SIZE #1 COOLANT TYPE New condition, as pictured.Payment due within 48 hours of purchase. Check, m/o, and PayPal accepted. $7.50 for USPS Priority Mail shipping with tracking.Thanks for looking!
More

High Speed Steel Taps -...

$4.99
Brownells High Speed Steel Taps - Bottom Tap, 6-48, 31, 25
+ $7.95 shipping
/high-speed-steel-taps/o6Rv74_3BnzK-6pwDTAZ0A==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co.
More

Tap,0-80 Multi-Colored

$7.07
Walmart.com Tap,0-80 Multi-Colored
Free Shipping
/tap080-multicolored/J8ZGIKbNV6daf2_pZAQsTA==/info
Walmart.com
IN_STOCK ( In stock )
Free Shipping
Threading taps like this size 0-80 are a must for any scratch builder or modeler. The threading taps complement the dies, and vice versa. Features Taps and dies constructed of high quality tungsten steel The threading dies compliment the taps and vice versa
More

Wire Gauge Carbon Taps -...

$2.49
Brownells Wire Gauge Carbon Taps - Taper Tap, 5-40, 38, 29
+ $7.95 shipping
/wire-gauge-carbon-taps/vQyDDXzGmLJwISbhAIxrRA==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co. SPECS: Those taps marked ** are high-speed steel. Others are U.S. made.
More

T-Handle Tap Wrench -...

$5.99
Brownells T-Handle Tap Wrench - T-Handle No. 1e, Size 0-12
+ $7.95 shipping
/thandle-tap-wrench/wJ2_eWzm2P2wfPsBHPQxoA==/info
Brownells
IN_STOCK ( In stock )
Store not rated
T-HANDLE TAP WRENCH Mfg: Brownells SPECS: No. 1E for 0 to 12. No. 164 for 1/16'''' to ¼''''
More

Wire Gauge Carbon Taps - Plug...

$2.49
Brownells Wire Gauge Carbon Taps - Plug Tap, 4-40, 43, 31
+ $7.95 shipping
/wire-gauge-carbon-taps/0fxoVgeLJf2hHLszgO4k6w==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co. SPECS: Those taps marked ** are high-speed steel. Others are U.S. made.
More

Wire Gauge Carbon Taps -...

$2.59
Brownells Wire Gauge Carbon Taps - Taper Tap, 8-32, 29, 16
+ $7.95 shipping
/wire-gauge-carbon-taps/2Xu9YgNjt0pbicRE96C4ew==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co. SPECS: Those taps marked ** are high-speed steel. Others are U.S. made.
More

Wire Gauge Carbon Taps -...

$2.59
Brownells Wire Gauge Carbon Taps - Taper Tap, 8-40, 28, 16
+ $7.95 shipping
/wire-gauge-carbon-taps/AgrS_fZo4635N7fw44Q71A==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co. SPECS: Those taps marked ** are high-speed steel. Others are U.S. made.
More

Wire Gauge Carbon Taps -...

$2.59
Brownells Wire Gauge Carbon Taps - Bottom Tap, 6-48, 31, 25**
+ $7.95 shipping
/wire-gauge-carbon-taps/HOJslwKh4KNo5OgXEWf72w==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co. SPECS: Those taps marked ** are high-speed steel. Others are U.S. made.
More

Wire Gauge Carbon Taps -...

$2.79
Brownells Wire Gauge Carbon Taps - Bottom Tap, 8-40, 28, 16
+ $7.95 shipping
/wire-gauge-carbon-taps/II14JsI1-OoTOWuXfZzwHw==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co. SPECS: Those taps marked ** are high-speed steel. Others are U.S. made.
More

Wire Gauge Carbon Taps -...

$5.99
Brownells Wire Gauge Carbon Taps - Bottom Tap, 3-56, 45, 36
+ $7.95 shipping
/wire-gauge-carbon-taps/L06JEFD9pNxms78QA0BwOA==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co. SPECS: Those taps marked ** are high-speed steel. Others are U.S. made.
More

Wire Gauge Carbon Taps -...

$5.99
Brownells Wire Gauge Carbon Taps - Taper Tap, 3-56, 45, 36
+ $7.95 shipping
/wire-gauge-carbon-taps/NkaFpOmpduQulyYg1AR5xA==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co. SPECS: Those taps marked ** are high-speed steel. Others are U.S. made.
More

Wire Gauge Carbon Taps -...

$2.59
Brownells Wire Gauge Carbon Taps - Taper Tap, 8-36, 29, 16
+ $7.95 shipping
/wire-gauge-carbon-taps/NtS2nVwC-5bARXp2cCryqg==/info
Brownells
IN_STOCK ( In stock )
Store not rated
We supply our taps in Carbon steel whenever possible. If one should break off in a hole, the remains can be shattered with a punch for easy removal. All numbers in chart are shown as Nominal Size, Tap Drill Size, Clearance Drill Size. Mfg: Irwin Industrial Tool Co. SPECS: Those taps marked ** are high-speed steel. Others are U.S. made.
More

TAP-3 Drum Tap, 2 In,...

$120.49
Walmart.com TAP-3 Drum Tap, 2 In, Polypropylene
Free Shipping
/tap3-drum-tap-2-in/VFYWCtdVzyjq9YuNd5PvAw==/info
Walmart.com
IN_STOCK ( In stock )
Free Shipping
Drum Tap, Seal Material Nitrile, (M)NPT Inlet 2 In., Material Polypropylene, Horizontal, Includes -, Standards - Features Type : Plastic Item : Drum Tap Body Material : Polypropylene Seal Material : Nitrile Color : Blue For Use With : 2 Drum Plugs (M)NPT Inlet : 2 Includes : - Cable Type : - Construction : - End Type : - Number Drums : - Pump Size : - Pump Type : - Characteristics : - Standards : - Disassembled Size : - Faucet Type : - Max. Content Flow : - Material : Polypropylene Horizontal/Vertic al : Horizontal
More

Prices are provided by the merchants. We assume no responsibility for accuracy of price information provided by merchants. Please alert us to any pricing discrepancies and we will alert the merchant. Sales taxes are estimated at the zip code level. Shipping costs are estimates. Please check store for exact shipping costs. To learn more about why certain stores are listed on the site, click here

Product specifications are obtained from third parties, and while we make every effort to assure the accuracy of product information, we do not assume any liability for inaccuracies. Store ratings and product reviews are written and submitted by online shoppers to assist you as you shop. They do not reflect our opinions. We take no responsibility for the content of ratings and reviews submitted by users.

Copyright © 2000-2015 eBay Inc. All Rights Reserved

http://img.shoppingshadow.com/jfe/JavaFrontEnd-fe143.sp14-28392
http://img.shoppingshadow.com/jfe/JavaFrontEnd-fe143.sp14-28392