SquareTrade © AP6.0 BRAND NEW INTERFIRE T-460 4-CHANNEL 800 WATT AMPLIFIER Key Features: Four Class AB high-current dual discrete drive stages Class AB technology MOSFET PWM power supply Bridgeable Tri-mode operation Continuously variable 12dB/octave high pass 12dB/octave low pass crossover Subwoofer variable crossover for deep bass control Enhanced bass boost +12dB@45hz Soft start muting Overload, thermal and short circuit protection Power protection indicator Silver plated RCA, p

Martin Roland (Acesonic) MA-3000K 600 Watts Professional Digital Mixing Amplifier If you are looking for the professional karaoke mixing amplifier for your bar or club, look no further than Martin Roland's MA-3000K 600 Watts Professional Digital Mixing Amplifier. Designed by German engineer, Martin Roland is known for its quality and durability. This professional mixing amplifier was built to sustain continuous usage at maximum wattage output. It is a perfect companion for DJs and KJs who are seeking for a reliable component that will carry them throughout the long night without the nightmare of equipment failure. Specification: Audio Output: 300W+300W Output @ 8 Ohm Microphone input sensitivity: 0 Less

General Features:600w Peak, 4-channel Power AmplifierPower Ratings: 8 Ohms: 80 Watts X 4 Chan.4 Ohms: 150 Watts X 4 Chan.25/70/100v: 150 Watts X 4 Chan.Convection Cooled So There's No Annoying Fan NoiseSwitchable 120v/240v Power Supply (internal)Front Panel: Signal Level L.e.d.’s On Each Channel Include –24,-18, -12, -6, -3 And Clip Alert Rear Panel: Level Attenuators For Each ChannelEuroblock InputsScrew Terminal OutputsSwitches To Select Between Two Choices Of Inputsensitivity And Hpf Frequencies On Each ChannelRemote Power Turn-on/off And Adjustable Turn-ondelay Up To Eight Seconds. 6-way Protection Circuitry (output Over-current, Dc Output, Main Supply Rail Over Voltage, Chassis Internal Temperature, Inrush Limiting And Main Fuse)1-year Manufacturer's WarrantySignal To Noise (20 Hz-20... Less

The Fender PRO series TB-600 combines 600 watts of power with total tonal finesse and versatility to produce thick, natural and balanced bass tone that sits perfectly in the mix onstage and in the studio. Based on the acclaimed Fender TBP-1 tube bass preamp, the key to its sound is the passive tone stack - the backbone of classic Fender guitar and bass amps - in which each control knob setting affects the sound of the other controls, producing big, warm notes.

Crown CTS600 2-Channel Power Amplifier, 300 Watts per ch. @ 4 Ohms/70V High power density in a 2RU chassis Crown Switching Power Supply for lighter weight Selectable "Constant- Voltage" or low-impedance (4/8 ohm) operation perchannel 100V direct outputs Legendary Crown class-I (BCA) and AB+B output topologies offer the best inamplifier reliability Comprehensive array of indicators provide accurate diagnostics Fully PIP2-compatible HiQnet compatible Power Output Dual mode, 2 ohms: 150W Dual mode, 4, 8 or 16 ohms or 70V: 300W Bridge mode, 4 ohms: 300W Bridge mode, 8 or 16 ohms or 140V: 600W Specifications Frequency Response (at 1 watt, 20Hz-20kHz): +/- 0.25dB Signal to Noise Ratio below rated power (20Hz to 20kHz): 105dB A-weighted Total Harmonic Distortion (THD) at full rated power, from... Less

JL Audio M600/1 M Series Monoblock Class D Car Amplifier RMS Power Rating (14.4V): 4 ohms: 400 watts x 1 chan. 2 ohms: 600 watts x 1 chan. RMS Power Rating (12.5V): 4 ohms: 300 watts x 1 chan. 2 ohms: 500 watts x 1 chan. Unregulated MOSFET switching type power supply NexD Ultra-High Speed Class D topology Wired JL Audio HD-RLC remote level control sold separately LED power (green) and protect (red/yellow) indicators State-of-the-art microelectronic components Mono channel operation Advanced Thermal Rollback System completely eliminates annoying thermal shut-down events Studio-grade signal processing with fully variable crossover filters Extruded aluminum alloy system setting security cover Total amplifier efficiencies exceeding 80% Noise-killing, highly flexible differential- balanced... Less

Outboard amplifier for Definitive in-wall subwoofers Drives either one or two subwoofers Volume Low-pass crossover and phase adjustments Five-way binding post speaker connectors The SubAmp 600 is a high powered amplifier and electronic crossover specifically engineered for use with the Definitive IWSub 10/10 and IWSub References in-wall subwoofers. It features two discrete high power amplifiers with simple connections in one convenient housing that fits easily on a shelf or in an audio equipment rack. It provides optimal power for effortlessly driving one or two IWSubs in the same room or in different zones. It also provides crossover functions for the system and level low-pass crossover frequency and phase can all be adjusted with convenient front-panel control knobs. Power Output One... Less

The Fender TB-600C Combo provides thick, natural and balanced tone that sits perfectly in the mix onstage and in the studio. Based on the critically acclaimed TBP-1 tube bass pre-amp, the key to its powerful tone is its passive tone stack, which is the backbone of classic Fender guitar and bass amps. In a passive tone stack, the working of each knob affects the others, resulting in big, warm notes. The Fender TB-600C combo delivers 400 watts to its internal 8-ohm load; 600 watts when paired with any 8-ohm external cabinet.

SquareTrade © AP6.0 Template By Froo! Rockford Fosgate T600-2 2 Channel 1200 Watt Amplifier Rockford Fosgate Power Series T600-2 2 Channel Amplifier New Compact Designed for easy installations. These were designed with the goal of being the Most powerful car amplifier per square inch. Brand New, Not Refurbished Features: Power Series Compact 2-Channel Amplifier RMS Power Output: 4 ohms: 200 watts x 2 channels 2 ohms: 300 watts x 2 channels Bridged, 4 ohms: 600 watts x 1 channels CEA-2006 compl

ROCKFORD CORP 600 Watt 4-Channel Amplifier w/24dB/octave crossover " border="0"> ROCKFORD CORP 600 Watt 4-Channel Amplifier w/24dB/octave crossover T600-4 780687324483 Brand: ROCKFORD CORP Condition: Brand New Factory Sealed with Full USA Warranty Sale Details: The T600-4 amplifier offers the perfect balance of power output & compact design required for high performance audio systems. The 4-channel configuration allows fine tuning adjustments between front stage component systems & rear surround speakers. The built-in crossover also allows the rear channels to be configured for running one or two subwoofers. * 2/4 channel switch * 24dB/octave crossover * 4 Gauge power/ground terminals * Audiophile grade speaker connections * MOSFET output stage * MOSFET power supply * RCApass-thru *... Less

The Samson SX1800 stereo power amplifier has been designed to provide robust, clean output with low distortion and wide dynamic range, along with the dependability demanded by professional audio engineers and installers. The convenient two rackspace design is compact, and yet there's plenty of power available, with 2 x 400 watts at 8 ohms and 2 x 600 watts at 4 ohms. For mono applications, a bridged mode links both channels of the amplifiers, thus providing even more power, with a power rating of 1200 watts for the SX1800 into an 8 ohm load. Input connections are made via combination connectors allowing for both balanced XLR and balanced 1/4? TRS connections. For the outputs, the SX1800 amplifier provides standard 5-way binding posts, as well as Speakon connectors. Front panel controls... Less

The PS400 is Engineered to maintain the integrity of the input signal and to exhibit noise floor levels acceptable only in professional recording environments, no corners were cut to save money on the PS600 design. The class D amplifier represents the next generation of digital amplifier technology and, coupled with the audiophile class pre-amp, the PS400 sets new standards in affordable instrument amplification. While the front panel suggests a basic three band EQ, the addition of the mid cut switch and the mid cut level control add an additional stage of tone shaping capability. Via the Epifani footswitch the mid cut and mute can be engaged or disengaged.

Product FeaturesHigh Power Professional Power Amplifier Power Handling8 Ohms: 600 Watts X 2 Chan. 4 Ohms: 1000 Watts X 2 Chan.2 Ohms: 1350 Watts X 2 Chan.Bridged @ 8 Ohms: 2000 Watts X 1 Chan.Bridged @ 4 Ohms: 3000 Watts X 1 Chan.Optimized For Maximum Headroom Into 2, 4 And 8 Ohm Speaker SystemsAir Guided Front-to-rear Airflow And Cooling Fan For Thermal Stability And ReliabilityXlr And Trs (6.5mm Jack) Balanced InputsAuto Limitation Circuit Built In For Amp Output ProtectionStereo, Parallel Mono And Mono BridgeVariable Speed Fan For Low NoiseComprehensiv e Front Panel Indicators Including Signal, Clip, Protect And Bridge3 Speakon Outputs For Channels A/b/bridge5-way Binding Banana Plug Channel OutputsBridge Control SwitchDc Output Protection And Short Circuit ProtectionGround Lift... Less

Store Home Accessories Subwoofer Grills Amp Installation Kits Capacitors Car Alarms CD MP3 Players Component Speakers DVD Players EQ Sound Processors Indash DVD Players Marine Audio Mono Amplifiers Multi Channel Amplifiers Navigation Sound Deadning Speakers Subwoofer Enclosures Subwoofers Others DLS Performance CAD 15 1600W, 1-Channel Class D Classic Series Monoblock Car Amplifier (Performance Classic -- 10-30215) Each purchase = 1 Brand New Amplifier! These are brand new, never used, not refur

If you are looking for the professional karaoke mixing amplifier for your bar or club, look no further than Martin Roland's MA-3000K 600 Watts Professional Digital Mixing Amplifier. Designed by German engineer, Martin Roland is known for its quality and durability. This professional mixing amplifier was built to sustain continuous usage at maximum wattage output. It is a perfect companion for DJs and KJs who are seeking for a reliable component that will carry them throughout the long night without the nightmare of equipment failure. Specification: MicrophonesVolume ControlEcho ControlMusic ControlFull Function Remote Control * Ultra Quiet Cooling Fan * Designed in Germany * Weight: 40 lbs * 3 x 1/4" Microphone Inputs * Input Signal Attenuators * Auto-gain level indicators * ... Less

Samson doesn't "just" manufacture some of the finest wireless systems in the world. They also make great power amps, like the high quality, very affordable Servo Series. These compact, durable amps pack a lot of punch and are versatile enough for both live and studio applications. All three models include circuitry protection against overheating and over current, and the Servo 200, 300 and 600 feature relay-controlled power-on circuitry that prevents speaker "thumps." To keep the Servo Series amplifiers running cool, their design employs twin internal wind tunnels with forced-air cooling via two temperature- sensitive, variable speed fans, which greatly reduce the chance of thermal and overheating problems. The sound is clean, powerful and transparent. This is truly professional sound at... Less

Make your drive to work more enjoyable; fit your car with the Jl Audio XD600/6 car amplifier. As a Class D amplifier with NexD switching amp technology, this Jl Audio car amplifier pumps out crisp sounds through minimal current consumption and less heat production. Connect subwoofers, music players and add-ons of your choice, as the Jl Audio XD600/6 has 6 channels. At an impedance of 4 ohms, this Jl Audio 6 channel amplifier delivers 75 Watts RMS Power so that no muffled or jarring sounds annoy when behind the wheel. The soft melodies will be heard as clearly as the rock booming as this Jl Audio car amplifier has a frequency response of 12 Hz - 22 kHz. Noise from your vehicle will not interfere with sound output as this Jl Audio 6 channel amplifier has differential balanced inputs to... Less

SOLD INDIVIDUALLY... 24 bit digital processor possibility of settings and adaptation to the room dynamics and dimensions 600 Watt Rms BASH¨ amplifier mated to a 13"(33cm) "W" cone the SW 1000 Be offers high level reproduction with a low roll-off at 18Hz and a sound pressure level achieving 119dB. Description 24 bit digital processor possibility of settings and adaptation to the room dynamics and dimensions 600 Watt Rms BASH® amplifier mated to a 13"(33cm) "W" cone the high end subwoofer SW 1000 Be offers high level reproduction with a low roll-off at 18Hz and a sound pressure level achieving 119dB. Technical specifications Type Active bass-reflex subwoofer. Standard finishes Basalt - Champagne - Slate Grey - Mahogany On demand finishes Other finishes subject to estimate Drivers 33cm... Less

The STM-600 is our 600 watt version of the Streamliner? design. The 300 volt All Tube Class A preamp design is driven by three 12AX7 preamp tubes utilizing six gain stages. The preamp design features an intuitive and highly effective tone network which is a unique blend of a modified passive Baxandall network for the bass and treble along with an active tube driven mid filter, with selectable mid frequencies. This versatile all tube preamp exudes a fat and rich tone that remains articulate. It can be used to simply add warmth to your natural tone or it can be dialed in to provide a wide range of natural tube overdrive. Along with our preamp design that rivals that of many classic tube amplifiers, the STREAMLINER? 600 also features our proprietary 3 Dimensional Power Management analog... Less

The T600-2 small chassis design and power output is a great alternative when power is a must and space is limited. Dont let its size fool you though this all MOSFET amp packs enough power to run one 2-Ohm DVC or two 4-Ohm DVC subwoofers with ease and its dual function EQ can tune-in any pair of high frequency component speakers for premium sound quality. * 24dB/octave crossover * 4 Gauge power/ground terminals * Audiophile grade speaker connections * MOSFET output stage * MOSFET power supply * CEA-2006 Compliant * RCA pass-thru * Number of Channels 2 * Rated Power * continuous power 200W x 2 @ 4-Ohms RMS * 300W x 2 @ 2-Ohms RMS * 600W x 1 @ 4-Ohms bridged RMS * 1-Ohm x 2 Stable * 2-Ohm x 1 bridged Stable * Total Power * total sum of rated power 600 Watts * Dynamic Power * powercube... Less

POWER ACOUSTIK Gothic Series Monoblock Class AB 1,600W #GT1-1600 This unit has a full 1 year factory warranty POWER ACOUSTIK #GT1-1600 GT11000: Monoblock Gothic Series Car Amplifier RMS Power Rating: 4 ohms: 375 watts x 1 chan. 2 ohms: 470 watts x 1 chan. Max power output: 1000 watts MOSFET power supply Pulse width modulation circuitry Bass Boost (0-12 dB bass boost at 45 Hz) Mono channel operation Preamp RCA outputs 3-Way system protection circuitry (short, thermal and overload) Heavy duty aluminum alloy heatsink Low level inputs (200mV-8V) Variable subsonic filter (20-50 Hz, 12 dB/octave) Frequency response: 10-35,000 Hz Dimensions: 9"L x 9-3/4"W x 2-3/10"H RCA level inputs Screw terminals Wired bass remote knob included Variable low-pass filter (40-150 Hz, 12 dB/octave) LED power... Less

New Acoustic Audio XS2402 2400 Watt 1/2-Channel Car Amplifier New Acoustic Audio Xtreme Series XS2402 2400 Watts 2 Channel MOSFET Car Amplifier Features: 2400 Watts Peak x 1 Channel @ 4 Ohms Bridged 1200 Watts RMS x 1 Channel @ 4 Ohms Bridged 600 Watts RMS x 2 Channels @ 2 Ohm 300 Watts RMS x 2 Channels @ 4 Ohm 2/1 Channel Operation Tri-Mode Capable Frequency Response: 20Hz-25kHz S/N Ratio: 90dB Channel Separation: 60dB THS%: 0.01 Input Sensitivity: 200m 6V Input Impedance (Low Level): 20K Ohms Full MOSFET Circuitry Thermal/Short/Ove rload Protection Power/Protection LEDs Heavy Duty Aluminum Alloy Heatsink Heavy Duty Block Terminals RCA Line Inputs (Low Level) Speaker Line Inputs (High Level Harness Included) Selectable LP/FULL/HP Crossover Adjustable Gain Control Full 1 Year Warranty... Less

Output power: 600W @ 4 ohms; 960W @ 2 ohms High continuous current output from robust toroidal transformer Switchable input peak limiter and selectable high pass filter (30Hz, 50Hz) to reduce distortion and protect Speakers Front mounted detented gain controls for easy access Bridge mono and parallel mode LEDs Fast Recovery design for lower distortion if clipping occurs Very rugged housing Active balanced inputs for low noise Signal level at -40, -20, -10, protect and clip LED indicators to monitor performance Ground Lift switch to prevent humming Selectable stereo, parallel & bridge mono amp modes Two ventilation variable speed Fans Speakon-type connectors and 5-way binding posts speaker outputs XLR & 1/4" TRS connectors for maximum input flexibility Requires... Less

SquareTrade AP6.0 Brand New In Box Lanzar VIBE 1200 WATTS 2 CHANNEL MOSFET AMPLIFIER VIBE232 Features: 2 x 300 Watts RMS @ 4 Ohms 2 x 600 Watts Max @ 4 Ohms 1 x 1200 Watts Max @ 4 Ohms Bridged 2 x 500 Watts @ 2 Ohms RMS MOSFET Automatically Switches to Maintain Rated Power Over a Wide Range of Battery Voltages Stiffly Regulated PWM-Type Power Supplies Variable Input Level Controls for Each Pair of Cannels Variable High Low Pass Crossover Controls High-Efficiency, Heavy Aluminum Heatsink Remote

Capacitors Changers Crossovers Equalizers Extended Warranty Head Units Marine Components Multimedia Systems Radar Detectors Satellite Radio JL Audio HD Series 4-Channel Class D, Small Profile Car Amplifier with R.I.P.S. Specifications: RMS Power Rating: 1.5-4 ohms: 150 watts x 4 chan. Bridged, 3-8 ohms: 300 watts x 2 chan. Max power output: 600 watts x 2 chan. MOSFET power supply Remote bass level input (HD-RLC required and sold separately) LED power indicators 4/2 channel operation Speaker-level inputs Preamp RCA outputs Single Cycle Control? Heavy duty aluminum alloy heatsink for heat dissipation RCA level inputs Screw terminals Variable high-pass filter (50-500 Hz, 24 dB/octave) Variable low-pass filter (50-500 Hz, 24 dB/octave) Frequency response: 20-20,000 Hz

Hard Driving Sound, the Q66 MKII has the Power to Drive a Huge Variety of Speaker Systems! Add Electro Voice’s Sx300, ZX4 or Sb122 to this incredible amplifier and revel in its incredible power. The Q Series utilizes an efficient Class-H amplifier design where the permanent voltage rail is designed to cover the average music signal, rather than continuing to supply the voltage for max output. When dynamic peaks need a higher output voltage the voltage rail switches over to maximum saving up to 50% of the power consumption and reducing heat output. Q Series combines the sonic excellence and ruggedness of its Precision Series predecessors with Class-H innovation, all in a compact and affordable package. Electro Voice Q66 MKII Features Easily Powers a huge variety of... Less

Accessories & Subwoofer Grills Amp Installation Kits Capacitors Car Alarms CD & MP3 Players Component Speakers DVD Players EQ & Sound Processors Indash DVD Players Marine Audio Mono Amplifiers Multi Channel Amplifiers Navigation Sound Deadning Speakers Subwoofer Enclosures Subwoofers Others MASSIVE AUDIO N2 1,600W Max Nano Block Series Monoblock Amplifier Each purchase = 1 Brand New Amplifier! Massive Audio N2 Nano Block Series Monoblock Car Amplifier RMS Power Rating (14.4): 4 ohms: 200 watts x 1 chan. 2 ohms: 400 watts x 1 chan. 1 ohm: 800 watts x 1 chan. Max power output: 1600 watts x 1 chan. MOSFET power supply with high grade switching devices LED power/protect indicators Selectable bass boost (0, 6, 12 dB switchable at 50 Hz) Monoblock operation Extreme power in a small footprint... Less

6-channel Class D M-series Marine AmplifierRms Power Rating @ 14.4v: 4 Ohms: 75 Watts X 6 Chan.2 Ohms: 100 Watts X 6 Chan.Bridged, 8 Ohms: 150 Watts X 3 Chan.Bridged, 4 Ohms: 200 Watts X 3 Chan.Rms Power Rating @ 12.5v: 4 Ohms: 60 Watts X 6 Chan.2 Ohms: 90 Watts X 6 Chan.Bridged, 8 Ohms: 120 Watts X 3 Chan.Bridged, 4 Ohms: 180 Watts X 3 Chan.Unregulated Mosfet Switching Type Power SupplyNexd Class D Technology Reduces Distortion And Delivers Superior EfficiencyFully Variable 12db/octave Filters With Filter Frequency Selection ControlsTwo Stereo Pairs (rca-type Jacks)3/4/5/6 Channel OperationSpeaker- level (high-level) InputsAdvanced Rollback Protection Circuitry For Advanced Thermal And Low-impedance ProtectionOptiona l Bass Knob: HdrlcDifferential Inputs Reduce Unwanted NoiseSpeaker... Less

GenzBenz's amplifiers from the Shuttle series was created for on-the-move bassists who need a flexible, full-featured combo system that is easily transportable and sounds good too.The core of the series is the lightweight Shuttle amplifier design. The 6.0 weighs only 3.75 lbs. and delivers 375 watts at 8 ohms and 600 watts at 4 ohms. Though this is a combo, the amp chassis can be easily removed from it's combo "saddle" quickly and carried to another gig in the pocket of your bass case or the available carry bag. The chassis has a handle too that makes carrying the cab, just as easy.The head is extremely useful as a standalone unit, with a headphone output that is excellent for quiet, personal practice sessions. You can adjust the volume level and tone you hear with the analog 12AX7 tube... Less

Brand New MTX Thunder TM601D Mono 600 Watt Marine Weather Resistant Boat Amplifier with splash resistant end panels Features MTX Thunder TM601D Mono Weather Resistant Boat Amplifier Splash resistant end panels protect feature controls using Plexiglass covers that prevent moisture intrusion into the amplifier chassis Intelligent Surface Mount Technology ensures electrical components are secured tightly to the PCB which increases the resistance to vibration RCA connections have rubber gaskets surrounding them preventing moisture from entering the pre-amp or corroding the connector, rubber boots also included to cover unused RCA's Stainless steel screws resist corrosion and gold plated terminals ensure maximum signal and current transfer Conformal Coated PCB and... Less