6.5 X257roberts Reloading Dies Sports and Outdoors - Shopping.com

Category

Sport and Outdoor
Showing results for "6.5 x257roberts reloading dies"
Results 1 - 40 of 1500+

RCBS 2-Die Set 6.5mm-257...

$150.99
MidwayUSA RCBS 2-Die Set 6.5mm-257 Roberts
+ $7.59 shipping
/rcbs-2die-set-65mm257/wk0aHMQEu30G5Rxyod0EOQ==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
RCBS has been making some of the best reloading equipment for over 60 years. Their 2-Die sets are known in many reloading circles for their high-quality. Each 2-Die Set includes a full length sizer die has an expander- decapping unit to remove the spent primer while expanding the case mouth. Vent holes prevent case damage caused by trapped air or excessive lubricant. The seater die includes a bullet seater plug and built-in roll or taper crimp as appropriate for the particular cartridge. Shellholders sold separately. Technical Information Material: Polished and Heat Treated Steel Accessories: Plastic Storage Case Notes: Lifetime Guarantee from RCBS
More

Nosler Custom Reloading Brass...

$66.99
MidwayUSA Nosler Custom Reloading Brass 6.5 Creedmoor Box of 50
+ $7.59 shipping
/nosler-custom-reloading/yjueWZKUFqcPIvrwPPZG8Q==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Nosler Custom Brass was developed to complement their line of custom bullets. Each lot is weight-sorted to provide consistent measurements and capacities for accurate loads and features a Nosler head-stamp. Before shipment, Nosler chamfers and deburrs the case mouths and deburrs the flash hole. Fully prepped and ready to load upon receipt, each piece of brass offers consistency in trimmed length and neck wall thickness. This brass is new and unprimed. This is not loaded ammunition. Technical Information Caliber: 6.5 Creedmoor Finish: Brass
More

RCBS Trim Die 257 Roberts

$35.99
MidwayUSA RCBS Trim Die 257 Roberts
+ $4.99 shipping
/rcbs-trim-die-257-roberts/tgRxbKINKbY2lom8nbPdiA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Doubling as a case length gage, this die will quickly allow the reloader to see if the case is too long. If the case is too long, the case will stick out above the top of the die. To get the case to the correct size, file the case down until it's flush with the top of the die. The Trim Die has been case hardened, hand polish and heat treated to withstand a file bearing against the top surface without causing damage to the die. Shellholder sold separately. Technical InformationMateri al: Heat-Treated Steel Die Type Included: Trim Die Accessories: Plastic storage case Notes: Standard 7/8-14 thread. The trim die doubles as a visual case length gauge. Run a case into the trim die and if the case stck out above the top of the die, it's too long. File the case down until it is flush with the... Less
More

Redding Trim Die 257 Roberts

$31.29
MidwayUSA Redding Trim Die 257 Roberts
+ $4.99 shipping
/redding-trim-die-257/xkIYvvshccedxdgU2e1q-Q==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Redding Trim Dies allow you to file trim your cases without unnecessary resizing because they are made to chamber dimensions. Other manufacturers use sizing die dimensions, forcing you to full length resize when trimming. For case forming and necking brass down from another caliber, Redding Trim Dies can be the perfect intermediate step before full length resizing. Technical InformationMateri al: Steel Die Type: Trim Die ONLY Accessories: Plastic storage case Notes: These trim dies allow you to file trim your cases without unnecessary resizing because they are made to chamber dimensions. This die requires an extended shellholder available from Redding. Form die must be purchased separately.
More

RCBS 2-Die Set 257 Roberts

$29.99
MidwayUSA RCBS 2-Die Set 257 Roberts
+ $7.59 shipping
/rcbs-2die-set-257-roberts/ozx9HNa98_Mkfsh8siFkzg==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
RCBS has been making some of the best reloading equipment for over 60 years. Their 2-Die sets are known in many reloading circles for their high-quality. Each 2-Die Set includes a full length sizer die has an expander- decapping unit to remove the spent primer while expanding the case mouth. Vent holes prevent case damage caused by trapped air or excessive lubricant. The seater die includes a bullet seater plug and built-in roll or taper crimp as appropriate for the particular cartridge. Shellholders sold separately. Technical Information Material: Polished and Heat Treated Steel Accessories: Plastic Storage Case Notes: Lifetime Guarantee from RCBS
More

Redding Deluxe 3-Die Set 257...

$79.99
MidwayUSA Redding Deluxe 3-Die Set 257 Roberts
+ $8.39 shipping
/redding-deluxe-3die-set/MVWW6YjsGVXEqJdkDtsLEA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Redding 3-Die Sets are available for rifle and pistol cartridges. The pistol sets contain a full length sizing die, expander die, and bullet seating die. The rifle sets contain a full length sizing die, neck sizing die, and a bullet seating die. The full length sizing die features a decapping rod assembly with neck expander. The expander die includes a neck expanding plug and the seating die features a built-in crimping ring and seating plug. This combination is sure to produce consistent, reliable ammunition time and time again. Shellholder sold separately. Made in the USA. Technical InformationMateri al: Steel Die Types Included: Full Length Sizer Die (with decapping unit) Expander Die for Pistol Sets and Neck Sizing Die for Rifle Sets Profile or Taper Crimp Seater Die (with built in... Less
More

Lee Factory Crimp Die 257...

$12.49
MidwayUSA Lee Factory Crimp Die 257 Roberts
+ $4.99 shipping
/lee-factory-crimp-die-257/EwnPydW4VmdCsTg68bd2kQ==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
The Lee Precision Factory Crimp Die is designed to give reloaders the perfect crimp on each round of reloaded ammunition. The Factory Crimp Die crimps the bullet more firmly in place than any other die with more uniform pressure. The Factory Crimp Die features a collet that squeezes the case mouth into the crimping groove for a firm hold. It is nearly impossible to buckle the case when crimping when compared to a regular roll crimp die. Lee's testing has shown that using a Factory Crimp Die provides a more uniform pressure curve, increasing the accuracy of any bullet. Shellholder sold separately. Technical Information Material: Steel Fits: Reloading presses that accept standard 7/8-14 Threads Accessories: Plastic Storage Box
More

Lee Reloading Stand Die Rack

$11.99
MidwayUSA Lee Reloading Stand Die Rack
+ $4.99 shipping
/lee-reloading-stand-die/urzrri7wbJ5ANbRHaa-dTg==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
The Lee Reloading Stand was designed just for the purpose of holding a reloading press so reloader could load up ammunition. Lee engineered these accessories to help ensure the loading process is as smooth as possible. The Die Rack was specially designed for the reloader looking to conveniently hold dies at the ready especially when loading up small batches of ammunition with frequent die changes. The great thing about the die rack is that it can either be mounted to the Lee Reloading Stand or mounted to any wall. Technical Information Fits: Lee Reloading Stand or can be mounted to any wall Function: Holds up to three dies in a convenient location Material: Steel
More

Lee Pacesetter 3-Die Set 257...

$31.99
MidwayUSA Lee Pacesetter 3-Die Set 257 Roberts
+ $7.59 shipping
/lee-pacesetter-3die-set/EuoDqh7CNfA_11xrnLJNSg==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Each Lee Precision has been manufacturing high quality, affordable reloading equipment since 1958. Each Pacesetter 3-Die Set includes the exclusive Lee Factory Crimp Die, Full Length Sizer Die and Bullet Seater Die. Each set is made from steel and includes the appropriate Shellholder, Powder Measure, load data, plastic storage box and a two year warranty. Adjustable crimp from slight taper to full roll. Technical Information Dies Included: Full Length Sizing Die Bullet Seating Die Factory Crimp Die Die Size: 7/8-14 threads Shellholder Required:Yes Shellholder Included: Yes Notes: 2 Year Warranty Accessories Included: Powder Dipper Load Data Plastic Storage Box
More

Redding 2-Die Neck Sizer Set...

$47.49
MidwayUSA Redding 2-Die Neck Sizer Set 257 Roberts
+ $7.59 shipping
/redding-2die-neck-sizer/IR8ORQD7qlDUQMrEG7L1cQ==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
The Redding Neck Sizer Die set includes a Neck Sizer Die with decapping/expande r unit and Bullet Seater Die with crimping ring and seater plug. They are machined from the finest quality alloy steel then heat treated in atmospherically controlled furnaces for super tight tolerances and a lifetime of use. Shellholder sold separately. Technical InformationMateri al: Steel Die Types Included: Neck Sizer Die (with decapping / expander unit) Seater Die (with built in crimping ring and seater plug) Accessories: Plastic Storage Case Spare Decapping Pin Notes: Shellholder Not Included
More

Forster Bench Rest 2-Die Set...

$64.12
MidwayUSA Forster Bench Rest 2-Die Set 257 Roberts
+ $7.59 shipping
/forster-bench-rest-2die/EehZ0IhK5O4sovPjtcpKNQ==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Polished steel die set includes the Forster Bench Rest Full Length Sizer Die and the Forster Bench Rest Seating Die. The non-crimping bullet seating die allows the bullet and case to be held in perfect alignment during seating. It is recommended that neck sizers be used only for Bolt Action of single shot rifles. Cartridges for autoloaders, lever action and pump rifles should be full length sized. Set includes the Forster Bench Rest Full Length Sizer Die and the Forster Bench Rest Seating Die. Shellholder sold separately. Technical Information SPECIAL NOTE: If using Forster Dies in a Forster Co-Ax press shellholders are not required since Forster presses do not require a shellholder. If using Forster Dies in any non-Forster press use shellholders that are recommended by the press... Less
More

RCBS Neck Sizer Die 257...

$32.29
MidwayUSA RCBS Neck Sizer Die 257 Roberts
+ $4.99 shipping
/rcbs-neck-sizer-die-257/pftvMfDDbFZKnOUOR8m6zg==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Neck Sizer Dies size only the neck of case (not the shoulder or body) just enough to snugly hold the bullet which leads to increase case life and accuracy. Technical InformationMateri al: Steel Die Type: Neck Sizer Die (with expander- decapping unit) Accessories: Plastic Storage Case Notes: Neck Sizer Dies size only the neck of the case (NOT the shoulder or body) just enough to snugly hold the bullet for extended case life and accuracy
More

Redding Neck Sizer Die 257...

$33.29
MidwayUSA Redding Neck Sizer Die 257 Roberts
+ $4.99 shipping
/redding-neck-sizer-die/zWL80rO60ZhqrrO3l3EAeA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Redding Neck Sizer Dies only size the neck of your bottleneck cases to prolong brass life and improve accuracy. It is important to note that since these dies size only the neck and not the shoulder or body, fired cases should not be interchanged between rifles of the same caliber. Made in the USA. Technical InformationMateri al:Steel Die Type Included: Neck Sizer Die ONLY Accessories: Plastic storage case
More

Redding 2-Die Set 257 Roberts...

$92.99
MidwayUSA Redding 2-Die Set 257 Roberts Ackley Improved 40-Degree Shoulder
+ $7.59 shipping
/redding-2die-set-257/0iZfAF5SFvGO6MX5fDqY6Q==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
The Redding 2-Die Set contains a full length sizing die with decapping rod assembly with a neck expander and seating die with bullet guide, built-in crimping ring and seating plug. All Redding products are produced with the highest quality materials and are thoroughly inspected to deliver the best product. Shellholder sold separately. Made in the USA. Technical InformationMateri al: Steel Die Types Included: Full Length Sizer Die (with decapping / expander unit) Seater Die (with built in crimping ring and seater plug) Accessories: Plastic Storage Case Spare Decapping Pin Allen wrench included for lock rings. Notes: Shellholder Not Included
More

RCBS Full Length Sizer Die...

$26.29
MidwayUSA RCBS Full Length Sizer Die 257 Roberts
+ $4.99 shipping
/rcbs-full-length-sizer/EGQP3j8IW1bOfOEYITC_Kw==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Full Length Sizer Dies for bottle neck cases have vents to prevent case damage caused by trapped air and to release excessive lubricants. Headspace is held to minimum tolerances to avoid changing the case body length during full-length sizing.Technical InformationMateri al: Steel Die Type Included: Sizer Die (With Decapping Unit) Accessories: Plastic storage case Notes: Resizes the full length of the case.
More

Nosler Custom Reloading Brass...

$76.99
MidwayUSA Nosler Custom Reloading Brass 6.5 Grendel Box of 50
+ $7.59 shipping
/nosler-custom-reloading/EtrCKozYQWDqdymUxVh8UQ==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Nosler Custom Brass was developed to complement their line of custom bullets. Each lot is weight-sorted to provide consistent measurements and capacities for accurate loads and features a Nosler head-stamp. Before shipment, Nosler chamfers and deburrs the case mouths and deburrs the flash hole. Fully prepped and ready to load upon receipt, each piece of brass offers consistency in trimmed length and neck wall thickness. This brass is new and unprimed. This is not loaded ammunition. Technical Information Caliber: 6.5 Grendel Finish: Brass
More

RCBS 2-Die Neck Sizer Set 257...

$48.29
MidwayUSA RCBS 2-Die Neck Sizer Set 257 Roberts
+ $7.59 shipping
/rcbs-2die-neck-sizer-set/msWJkzxz0703WXfhXXgV8Q==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Neck Sizer Dies resize only the neck of case just enough to snugly hold the bullet. This leaves the shoulder and body at their fire-formed dimensions which leads to longer case life and increased accuracy. For use with bolt action rifles only. New brass must be full length sized and fired before it can be neck sized. Set includes a Neck Sizer Die with Expander- Decapping Unit and a Seater Die with Seater Plug. Shellholder sold separately. Technical InformationMateri al: Polished and Heat Treated Steel Accessories: Plastic Storage Case Notes: Lifetime Guarantee from RCBS
More

Lee Collet 2-Die Neck Sizer...

$31.99
MidwayUSA Lee Collet 2-Die Neck Sizer Set 257 Roberts
+ $4.99 shipping
/lee-collet-2die-neck/U-9UJTxwahQdEkMUeIsRkQ==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Set includes Collet Neck Sizer Die, Bullet Seating Die, Shellholder, Powder Measure, charge table and storage box.. A collet in the sizing die squeezes the case neck against a precision mandrel for a perfect bullet fit with minimum bullet run-out. Technical InformationMateri al: Steel Die Types Included: Collet Neck Sizer Die (with decapping unit) Bullet Seater Die Accessories: Shellholder Powder Dipper Load Data Sheet Plastic Container Notes: Collet neck sizer uses a collet to squeeze the case neck against a mandrel, creating a precisely aligned case neck while reducing runout. No lubrication necessary when neck sizing only.
More

Lee Pacesetter 2-Die Set 257...

$35.99
MidwayUSA Lee Pacesetter 2-Die Set 257 Roberts Ackley Improved 40-Degree Shoulder
+ $7.59 shipping
/lee-pacesetter-2die-set/rC6E2h_nNP3AyT5sm1XheA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Lee Limited Production Pacesetter Die Sets are built to last a lifetime and are great at producing factory like ammunition. Each 2-Die set comes shipped with a Full-Length Sizer die and Bullet seating die. Also included is the appropriate shellholder, load data sheet and powder dipper. These dies are typically produced in small runs throughout the year. Inventory is subject to availability. Technical Information Material: Steel Die Types Included: Sizer Die Bullet Seater die with built in Roll Crimp Accessories: Shellholder Powder Dipper Load Data Sheet Plastic Container Notes: Adjustable crimp
More

Forster Bench Rest 2-Die Set...

$82.99
MidwayUSA Forster Bench Rest 2-Die Set 257 Roberts Ackley Improved 40-Degree Shoulder
+ $7.59 shipping
/forster-bench-rest-2die/Aof1SFfRaAr-ggWxyJtTAw==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Polished steel die set includes the Forster Bench Rest Full Length Sizer Die and the Forster Bench Rest Seating Die. The non-crimping bullet seating die allows the bullet and case to be held in perfect alignment during seating. It is recommended that neck sizers be used only for Bolt Action of single shot rifles. Cartridges for autoloaders, lever action and pump rifles should be full length sized. Set includes the Forster Bench Rest Full Length Sizer Die and the Forster Bench Rest Seating Die. Shellholder sold separately. Technical Information SPECIAL NOTE: If using Forster Dies in a Forster Co-Ax press shellholders are not required since Forster presses do not require a shellholder. If using Forster Dies in any non-Forster press use shellholders that are recommended by the press... Less
More

Norma USA Reloading Brass...

$25.99
MidwayUSA Norma USA Reloading Brass 6.5mm-284 Norma Box of 20 (Bulk Packaged)
+ $4.99 shipping
/norma-usa-reloading-brass/FKNm24cYLim70QP-al7iHA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Norma USA Brass is world renowned as being the absolute highest quality brass available. These cases start off with the best possible raw materials with the narrowest tolerances. The case necks are annealed to soften the brass and prevent gas leaks the case body is at the optimum hardness to avoid any unnecessary stretching. New, unprimed brass that features chamfered and deburred case mouths and a punched flash hole (magnum calibers are drilled). These cases should be sized before loading. This is not loaded ammunition. Technical Information Caliber: 6.5-284 Norma Finish: Brass
More

Forster Bench Rest Neck Sizer...

$36.99
MidwayUSA Forster Bench Rest Neck Sizer Die 257 Roberts
+ $7.59 shipping
/forster-bench-rest-neck/R6bLr33hE_N4KPikzKwLMA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
For reloaders who choose to retain the fire formed dimensions of cases rather than resizing the entire case, neck sizing-only dies fit a definite need. Although they only work the necks of cases, they do eliminate some problems associated with excessive headspace. Neck sizing can also prolong case life. All Forster Sizer Dies are equipped with the exclusive E-Z Out Expander. The floating E-Z Out Expander corrects misalignment of the center spindle assembly and prevents the case neck from pulling off-center during the expanding procedure. Shellholder sold separately. Technical Information SPECIAL NOTE: If using Forster Dies in a Forster Co-Ax press shellholders are not required since Forster presses do not require a shellholder. If using Forster Dies in any non-Forster press use... Less
More

Redding Type S Bushing Full...

$91.99
MidwayUSA Redding Type S Bushing Full Length Sizer Die 257 Roberts
+ $7.59 shipping
/redding-type-s-bushing/y4ucEur1lDwWY4yJuPY_iA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
The Redding Type S Full Length Sizing Die sizes the entire case while maintaining exact control of the case neck. It uses the same interchangeable bushings (sold separately) that are used in the Redding Bushing Style Neck Sizing Dies. Features an adjustable decapping rod that allows adjustment of the bushing position and a decapping pin retainer that enables neck sizing without the use of the size button for those who turn their case necks for uniformity. Shellholder sold separately. Technical InformationMateri al: Steel Die Type Included: Full Bushing Die Notes: All Type S dies are supplied with both the standard size button and a decapping pin retainer.
More

Lapua Reloading Brass 300 AAC...

$79.99
MidwayUSA Lapua Reloading Brass 300 AAC Blackout Box of 100
+ $7.59 shipping
/lapua-reloading-brass-300/dPFwRC7akER4magmtiN7rA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Lapua World-class brass begins with high-quality raw materials and superior smelting and metallurgical competence. Throughout the production process, the focus on quality control is consistent with Lapua's exacting standards. Particular attention is paid to hardness, solidity and grain structure. All Lapua brass is tested to 30% overpressure according to Commission Internationale Permanente, the agency that oversees ammunition and component producers in Western Europe. Technical Information Caliber: 300 AAC Blackout Finish: BrassNew, unprimed brass should always be resized before loading. This brass has undergone factory annealing which extends brass life, as a result of the annealing process the neck portion of the brass may be discolored until the case is cleaned. This is not loaded... Less
More

Forster Bench Rest Full...

$36.99
MidwayUSA Forster Bench Rest Full Length Sizer Die 257 Roberts
+ $4.99 shipping
/forster-bench-rest-full/J2-wtKnKtaEGnT-ZU_5Tmg==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
The Forster Bench Rest Full Length Sizer Die offers maximum flexibility. It will return brass to factory new specifications. But, if you're loading for the same firearm, the full length sizing die may be backed off' to partially resize and retain the fire formed dimensions of the case. All Forster Sizer Dies are equipped with the exclusive E-Z Out Expander. The floating E-Z Out Expander corrects misalignment of the center spindle assembly and prevents the case neck from pulling off-center during the expanding procedure. Shellholder sold separately. Technical Information SPECIAL NOTE: If using Forster Dies in a Forster Co-Ax press shellholders are not required since Forster presses do not require a shellholder. If using Forster Dies in any non-Forster press use shellholders that are... Less
More

Redding Neck Sizer Die 257...

$58.49
MidwayUSA Redding Neck Sizer Die 257 Roberts Ackley Improved 40-Degree Shoulder
+ $4.99 shipping
/redding-neck-sizer-die/VafilSeJkGPsf4GSIMqXgw==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Redding Neck Sizer Dies only size the neck of your bottleneck cases to prolong brass life and improve accuracy. It is important to note that since these dies size only the neck and not the shoulder or body, fired cases should not be interchanged between rifles of the same caliber. Made in the USA. Technical InformationMateri al:Steel Die Type Included: Neck Sizer Die ONLY Accessories: Plastic storage case
More

Norma USA Reloading Brass 257...

$138.99
MidwayUSA Norma USA Reloading Brass 257 Weatherby Magnum Box of 100 (Bulk Packaged)
+ $9.19 shipping
/norma-usa-reloading-brass/uCAMTGCN3dlcjjYsGv_jTA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Norma USA Brass is world renowned as being the absolute highest quality brass available. These cases start off with the best possible raw materials with the narrowest tolerances. The case necks are annealed to soften the brass and prevent gas leaks the case body is at the optimum hardness to avoid any unnecessary stretching. New, unprimed brass that features chamfered and deburred case mouths and a punched flash hole (magnum calibers are drilled). These cases should be sized before loading. This is not loaded ammunition. Technical Information Caliber: 257 Weatherby Magnum Finish: Brass
More

Norma USA Reloading Brass 257...

$29.99
MidwayUSA Norma USA Reloading Brass 257 Weatherby Magnum Box of 20 (Bulk Packaged)
+ $12.39 shipping
/norma-usa-reloading-brass/xqCxITRQIPM7OHYTZBu18g==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Norma USA Brass is world renowned as being the absolute highest quality brass available. These cases start off with the best possible raw materials with the narrowest tolerances. The case necks are annealed to soften the brass and prevent gas leaks the case body is at the optimum hardness to avoid any unnecessary stretching. New, unprimed brass that features chamfered and deburred case mouths and a punched flash hole (magnum calibers are drilled). These cases should be sized before loading. This is not loaded ammunition. Technical Information Caliber: 257 Weatherby Magnum Finish: Brass
More

RCBS 2-Die Neck Sizer Set 257...

$61.99
MidwayUSA RCBS 2-Die Neck Sizer Set 257 Roberts Ackley Improved 40-Degree Shoulder
+ $7.59 shipping
/rcbs-2die-neck-sizer-set/SDZw9vXbZ-LG1-ZYDKQ8og==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Neck Sizer Dies resize only the neck of case just enough to snugly hold the bullet. This leaves the shoulder and body at their fire-formed dimensions which leads to longer case life and increased accuracy. For use with bolt action rifles only. New brass must be full length sized and fired before it can be neck sized. Set includes a Neck Sizer Die with Expander- Decapping Unit and a Seater Die with Seater Plug. Shellholder sold separately. Technical InformationMateri al: Polished and Heat Treated Steel Accessories: Plastic Storage Case Notes: Lifetime Guarantee from RCBS
More

Hornady Custom Grade New...

$21.49
MidwayUSA Hornady Custom Grade New Dimension Bullet Seater Die 25-06 Remington, 257 Roberts
+ $4.99 shipping
/hornady-custom-grade-new/WQOc_1kDxmfT0o1b67aogA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
The Hornady Custom Grade New Dimension Seater Die is a great die for the avid reloader. The CGND Seater Die will improve your bullet seating and accuracy with its floating bullet alignment sleeve and stem. The floating sleeve is designed to align the bullet and case prior to seating, preventing any deformations on the base of the bullet. The Seater Die features a roll crimp. For the ultimate accuracy and precision, you can add the Hornady Microjust Seating Stem (sold separately #394708) to create your own Micrometer Seating Die! The CGND Seater Die is also compatible with popular bullets like the A-Max and FTX bullet lines with the addition of the appropriate Hornady Die Seater Stem (sold separately). Shellholder sold separately. Technical InformationMateri al: Steel Die Type: Seating Die... Less
More

Nosler Custom Reloading Brass...

$53.99
MidwayUSA Nosler Custom Reloading Brass 6.5x55mm Swedish Mauser Box of 50
+ $7.59 shipping
/nosler-custom-reloading/F8mhYI_GJ3yI-W9l5jBLag==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Nosler Custom Brass was developed to complement their line of custom bullets. Each lot is weight-sorted to provide consistent measurements and capacities for accurate loads and features a Nosler head-stamp. Before shipment, Nosler chamfers and deburrs the case mouths and deburrs the flash hole. Fully prepped and ready to load upon receipt, each piece of brass offers consistency in trimmed length and neck wall thickness. This brass is new and unprimed. This is not loaded ammunition. Technical Information Caliber: 6.5x55mm Swedish Mauser Finish: Brass
More

Hornady Reloading Brass...

$37.99
MidwayUSA Hornady Reloading Brass 6.5x55mm Swedish Mauser Box of 50
+ $7.59 shipping
/hornady-reloading-brass/U1t69nAV2ePum1RmHwHvNA==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Hornady produces brass with the same precision, attention to detail and focus on perfection that has made them a world leader in bullets. They measures their brass for consistent wall concentricity, tests pressure calibration to ensure uniform case expansion and hand-inspects each piece. This dedication to quality ensures proper seating of the bullet both in the case and in the chamber and consistent charges and pressures. The result is optimal velocity and repeatable accuracy from your cartridges. New, unprimed brass. This is not loaded ammunition. Technical Information Caliber: 6.5x55mm Swedish Mauser Finish: Brass
More

Robert Welch Signature 6.5...

$64.95
Crate & Barrel Robert Welch Signature 6.5 Chef's Knife
Free Shipping
/robert-welch-signature/v5bjDnICNOKpqJm-5WukgQ==/info
Crate & Barrel
IN_STOCK ( In stock )
Free Shipping
Open Stock Knives: Robert Welch Signature 6.5 Chef's Knife - Designed and engineered by Robert Welch Designs in the English Cotswolds, this Signature chef's knife offers the home chef a unique value with a new hybrid of European and Asian cutting-edge technologies. Its classic wide blade is efficient for the repetitive slicing, dicing, mincing and chopping of fruits, vegetables and meats. Rated in the top 1% of all brand knives by CATRA Cutlery and Allied Trades Research Association for their initial sharpness and edge retention, Signature knives have
More

Prvi Partizan Reloading Brass...

$29.99
MidwayUSA Prvi Partizan Reloading Brass 6.5x55mm Swedish Mauser Bag of 50
+ $7.59 shipping
/prvi-partizan-reloading/5Og3_aAXXKUFU3R_T_IqBg==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Prvi Partizan is offering a wide range of cartridge cases for hand loaders. These components are made of high quality raw materials, tested in a modern proof laboratory, with sever control during production process. Their characteristics will provide the assembling of extremely accurate and safe ammunition. The cartridge cases of PPU can be reloaded several times, without losing its quality, that's why they are very appreciated and demanded on the world market. New, unprimed brass. This is not loaded ammunition. Bulk brass should be full-length sized, trimmed and chamfered before loading. Preparation: Due to the manufacturing process and/or shipping, case mouths may not be perfectly round. To ensure a round case mouth, cases must be sized (or have the expander ball of the sizing die run... Less
More

Norma USA Reloading Brass...

$21.99
MidwayUSA Norma USA Reloading Brass 6.5x55mm Swedish Mauser Box of 25
+ $4.99 shipping
/norma-usa-reloading-brass/ZKcq2UoMyetmBCTJcpgBXQ==/info
MidwayUSA
IN_STOCK ( In stock )
Store not rated
Norma USA Brass is world renowned as being the absolute highest quality brass available. These cases start off with the best possible raw materials with the narrowest tolerances. The case necks are annealed to soften the brass and prevent gas leaks the case body is at the optimum hardness to avoid any unnecessary stretching. New, unprimed brass that features chamfered and deburred case mouths and a punched flash hole (magnum calibers are drilled). These cases should be sized before loading. This is not loaded ammunition. Technical Information Caliber: 6.5x55mm Swedish MauserFinish: Brass
More

Prices are provided by the merchants. We assume no responsibility for accuracy of price information provided by merchants. Please alert us to any pricing discrepancies and we will alert the merchant. Sales taxes are estimated at the zip code level. Shipping costs are estimates. Please check store for exact shipping costs. To learn more about why certain stores are listed on the site, click here

Product specifications are obtained from third parties, and while we make every effort to assure the accuracy of product information, we do not assume any liability for inaccuracies. Store ratings and product reviews are written and submitted by online shoppers to assist you as you shop. They do not reflect our opinions. We take no responsibility for the content of ratings and reviews submitted by users.

Copyright © 2000-2016 eBay Inc. All Rights Reserved

http://img.shoppingshadow.com/jfe/JavaFrontEnd-jfe.2016.pixel.MediaMath-30410
http://img.shoppingshadow.com/jfe/JavaFrontEnd-jfe.2016.pixel.MediaMath-30410