Item No.317 - 0504 A top quality product and ship to all U.S. A real picture of product. Shipping charge for most countries is USD 45.00 Specifications: Diameter of table: 4" Morse taper center hole: MT2 Diameter of center hole: 0.78"x 0.31" Center height for vertical mounting: 2.75" Width of T slot: 0.236" 4 T slots Width of locating key: 0.3937" Transmission ratio of worm gear: 1:72 Readout of hand wheel: 2' Minimum value of vernier: 10" Indexing accuracy: 120" Maximum working load: 44 lbs (

A rotary table is one of the most important accessories you can add to a mill. It is said that a mill and a rotary table is the minimum combination of tooling required for a machine to be able to duplicate itself. Mounted on the mill it accurately rotates a part under the cutter. It can be used to drill circular hole patterns, mill the spokes of a wheel, cut gears, flats on a bolt head, splines on a shaft, machine circular parts and more. The 4" diameter table has 4 T-slots for mounting parts and a threaded center hole that goes all the way through the table. The table can be mounted horizontally using angle clamps and T-nuts provided or it can be mounted vertically using the optional 3701 right angle attachment or 3750 tilting angle table. In the vertical position parts can be held... Less

4" diameter table size #2 Morse taper center hole The rotary table has lock down clamps and the crank can be disengaged The table is 2.76" high when horizontal, and the centerline is 2.76" above the table when in the vertical position The worm ratio is 72 to 1 10 second vernier reading Gear ratio 90:1 Number of T-slots: 4 Squareness: .0008" Parallelism (face to face): .0004" Maximum spacing error: 1 minute, 20 second To combine shipping, please purchase all items needed without paying and email

4-Inch diameter, 4 Slots Whole Degree Scale on the Dial, Worm Gear Drive Lash adjustment screw, reference lines Ball bearing rotary support, 2 6mm by 60mm clamping studs 2 t-nuts, 2 clamping straps, Manufacturer: Steelex

4" ROTARY TABLE VERT. / HORIZONTAL 4" diameter table size #2 Morse taper center hole The rotary table has lock down clamps and the crank can be disengaged The table is 2.76" high when horizontal, and the centerline is 2.76" above the table when in the vertical position The worm ratio is 72 to 1 10 second vernier reading Gear ratio 90:1 Number of T-slots: 4 Squareness: .0008" Parallelism (face to face): .0004" Maximum spacing error: 1 minute, 20 second

This horizontal / vertical rotary table is made of precision machined cast iron and has a 2 Morse taper center hole. The table is graduated with a 360 degree scale. The rotary table is furnished with lock down clamps. This rotary table comes with an adapter to mount a 3" lathe chuck. It works with both 3- and 4-jaw chucks. The table is 2.87" high when horizontal, and the centerline is 2.68" above the table when in the vertical position. The body of the table is 5" (crank handle to back) by 5.5" (mounting slot to mounting slot). The worm ratio is 72 to 1. Flatness of clamping surface: 0.0008". Parallelism of clamping surface to base: 0.0008". Squareness of clamping surface to angle face: 0.0012". Squareness of clamping surface to center slot: 0.0012". Concentricity of center bore:... Less

High Precision Rotary Table, Rack And Pinion, Rotation Angle (deg.) 0 To 190, Torque (in.-lbs.) 11.06 In-lb / 102 Psi, Bore 10mm, Cushion Type Shock Pads, Both Directions, Port Size M5 X 0.8, Maximum Pressure 87 Psi, Operating Temp. Range 32 To 140 F, Shaft Type Anodized Aluminum Table, Housing Material Anodized Aluminum, Powertrain Material Carbon Steel, Length 109.7mm, Width 55.4mm, Height 34mm

This is a Brand New Shop Fox 4" Rotary Table with Set of Clamps in a Wooden Storage Box for machining. Here are the details: PERFECT ROTARY TABLE FOR DOING SMALL PRECISION MACHINING T-SLOTTED TABLE HAND WHEEL SCALE GRADUATED IN ARC MINUTE INCREMENTS, NUMBERED EVERY 1 DEGREE TABLE SCALE GRADUATED IN 5 DEGREE INCREMENTS, NUMBERED EVERY 10 DEGREES WORM GEAR DRIVE, 36:1 RATIO (1 HANDLE ROTATION = 10 DEGREES OF TABLE ROTATION) LASH ADJUSTMENT SCREW, REFERENCE LINES & BALL BEARING ROTARY SUPPORT CAN BE POSITIONED HORIZONTALLY OR VERTICALLY INCLUDES: 2 Each - 6 mm clamping studs, 2-3/8" long, T-nuts, clamping straps & steps COMES IN A BEAUTIFULLY FINISHED WOODEN STORAGE BOX NOTE: CENTER HOLE ON TABLE DOES NOT GO ALL THE WAY THROUGH & IS NOT MORSE TAPERED

SHARS Horizontal and Vertical Rotary Table 4 NEW Product Code 202-2000 Product description Table diameter: 4"Height OA horizontal: 2.76"Center height: 2.76"Morse taper: 2 T-slot width: .236" Product features Low Profile 10 second vernier reading Gear drive immersed in oil Extra deep coolant channel Dual positive action locks Satin chrome dials Maximum individual spacing error 4" table 120", 6" table 80", 8, 10, 12, 16" tables 60"4" table utilizes low profile locks for added workspace Gear ratio

Based on the 3700 4" rotary table, this stand-alone CNC indexer can make your dividing and indexing jobs easy. Instead of cranking the rotary table handwheel by hand, you simply input your desired divisions or degrees and hit the NXT (Next) button. The stepper motor accurately advances the table to your preprogrammed position. You can divide a circle into from 1 to 999 divisions or into degrees to three decimal places at the touch of a button. The internal memory chip can store two programs of up to 40 steps each with up to four programmable parameters for each step. Resolution of the stepper motor is .0125° per step or 28,800 steps per revolution ±.006°/step based on 400 steps per revolution and a 72:1 worm gear. Rotation speed is programmable between 1°/second and 50°/ second. The unit... Less

** PHASE II **12" Tilting Rotary Table Manufacturer # 222-412 Item is new, on pallet. Ready for shipping. SHIPPING: item will need to be freighted. It is buyers responsibility to arrange freight. We have a standard loading dock, and will load the item at no additional fee. We have a local freight company called " R L Freight" that works great. You will need to call them, request a quote for zip code 63115 Weight: 345 SHIPPED Item is crated on standard pallet Specs:Brand Phase II Type Rotary Tabl

Rotary Slide Tilting Table, For Use With Drill Presses, Milling Machines, Grinders, Special Machines, For Accurate Set Up For Boring, Drilling, Reaming, Tapping, Grinding And Milling Operations, Capacity 10 In Diameter, Cast Iron, Cross Feed 4 In., Long Feed 4 In., 5/8 T-slots, Travel Movement/revoluti on 360 Degrees, Height 5 5/8 In., Includes 1 5/8 In Diameter Center Bore, 5/8 In X 1 In T-slots, Graduations Of 3 Minute Readings On Vernier Dial, Rim Calibrated 1 Degree Increments, 40 To 1 R

4 T-Slots for 3/8-Inch Studs 4 Degree per rotation of the hand wheel 10 minute vernier resolution Whole Degree marks on table Coolant trough and the worm gear can be easily disengaged for quick setting angles, mt no.2 center hole, approximate weight: 49 pounds, Manufacturer: Steelex

Rotary table for machinist. This 4" Rotary Table with Divider Plates is made for horizontal or vertical use. The vernier scale reads to 10 seconds. 1:72 Ratio or 5° per revolution. Includes 3 dividing plates, sector arms, indexing pin/handle, coolant trough and 10mm locating wrench. Specifications: Horizontal or Vertical Use 4- 5/16" T-Slots 1:72 Ratio or 5° Per Revolution Vernier Scale Reads to 10 Seconds Center Thru Hole on table has a #1 Morse taper (MT1) 3 Dividing Plates Sector Arms Indexing Pin/Handle MT #1 Spindle Bore Coolant Trough 10mm Locating Key

SB1363 South Bend 4 Inch Rotary Table Unique 6-slot design Mounts horizontally or vertically Satin chrome handwheel and dial Morse Taper #2 socket Dual table locks Worm gear lash adjustment and lock Degree scale on table edge Vernier scale is calibrated to 10 seconds To view the manual for this item, please click on the link below: http://cdn2.grizzl y. com/manuals/sb136 3_m.pdf Ship anywhere within the lower 48 states for $23.95! Please send us a message through eBay if you are shipping to Alaska

ACCURA/VERTEX HV-4 4 INCH HORIZONTAL/VERTIC AL ROTARY TABLE This little beauty is from a world class Taiwanese factory! It features 3 3/8 inch t-slots for fastening the work to the table and is constructed of high density Meehanite casting. It is inspected by the HEIDENHAIN process and is guaranteed flat and parallel. Gear ratio is 90 to 1 and the worm is hardened and ground. The table is graduated a full 360 degrees and the micro adjust collar is graduated in steps of 1 minute. Vernier scale ma

Ganro DR-202R 4th axis rotary table***no motor included*** s Diameter of Table mm / inch Ø200 / 7.87" Diameter of Thru-hole mm / inch Ø35 / 1.37" Center Height in Vertical mm / inch 135 / 5.31" Overall Height in Vertical mm / inch 247 / 9.72" Overall Height in Horizontal mm / inch 165 / 6.49" Width of T Slot mm 12 H7 Width of Guide Block mm 18 h7 Servo Motor Type FANUC 4i MITSUBISHI HF-44 HF-153 SIEMENS 1FK7042 1FK7063 HEIDENHAIN QSY96G QSY116E Total Reduction Ratio 1:90 MIN. Increment deg.

VERTEX HV-4 4"ROTARY TABLE This table is made of high density Meehanite, and is Electronically inspected (using HEIDENAHIN INSPECTION) for Excellent quality, durability and precision. Has a ground and hardened worm gear. Ratio is 90 to 1. The work table is graduated a full 360 so that one turn of the handle moves the table through 4 degrees. Micro collar is graduated. Precision Vernier Scale. MT-2 Center Sleeve can be used horizontally or vertically. See our other listings for dividing plates and tail stocks for these tables.

Ganro 4th axis rotary table***no motor included*** s DR-122R DR-152R DR-172R DR-202R DR-252R DR-322R DR-402R DR-502R DR-632R DR-802R Diameter of Table mm / inch Ø120 / 4.72" Ø150 / 5.90 Ø170 / 6.69" Ø200 / 7.87" Ø250 / 9.84" Ø320 / 12.59" Ø400 / 15.74" Ø500 / 19.69" Ø30 / 1.18" 250 / 9.84" 310 / 12.2" 400 / 15.74" 480 / 18.89" 205 / 8.07"

This is a version of the 3700 manual rotary table, except the worm housing has been replace with one that has a stepper motor mount at the end instead of a handwheel. A NEMA 23 size stepper motor is attached to the mount. If a dual shaft type motor is used, a handwheel (included) can be attached to the rear of the stepper motor for manual operation if desired. Sherline offers optional stepper motors as P/N 67127 or 67130 or you can use your own NEMA 23 motor, but the rotary table cannot be operated manually or CNC until a stepper motor is mounted. The table includes the same mounting clamps and chuck adapter as the 3700 manual table.

Wall Mount Table with 2-1/4" Backsplash 60"W x 24"D Stainless Steel Wall Mount Table is made with a 16 gauge, type 304 stainless steel top with 2-1/4" backsplash. 16 gauge, type 430 stainless steel wall bracket allows maximum stability while enabling full utilization of space underneath. Welded construction provides extra strength and durability. Top is polished to a # 4 blended finish. Measures 60"W x 24"D. NSF Listed. 60.00 L. 24.00 W.

This Brand New in the Box M1076 4" Rotary Table Description: This 4" Rotary Table is perfect for those doing smaller, precision work and features whole degree scale on the dial, worm gear drive and a lash adjustment screw. Specifications: 4" Diameter 4 Slots Whole Degree Scale on the Dial Worm Gear Drive Lash Adjustment Screw Reference Lines Ball Bearing Rotary Support 2 6mm x 60mm Clamping Studs 2 T-Nuts 2 Clamping Straps

This Brand New in the Box M1077 4" Rotary Table with Divider Plates Description:This 4" Rotary Table with Divider Plates is made for horizontal or vertical use. The vernier scale reads to 10 seconds. 1:72 Ratio or 5" per revolution. Includes 3 dividing plates, sector arms, indexing pin/handle, coolant trough and 10mm locating wrench. Specifications: Horizontal or Vertical Use 4-5/16" T-Slots 1:72 Ratio or 5° Per Revolution Vernier Scale Reads to 10 Seconds 3 Dividing Plates Sector Arms Indexing

If you have purchased a Sherline CNC system and wish to add the 4th or rotary axis, this rotary table with stepper motor is ready to plug right in. The EMC software is already 4-axis capable and there are 4 drivers installed in the driver box. The 5-pin mini-DIN connector on the stepper motor is ready to plug into the A-axis cable to make your system capable of 4-axis machining.

? The perfect rotary table for all you model makers and those doing smaller, precision work ? Features a whole degree scale on the dial, worm gear drive, lash adjustment screw, reference lines and ball bearing rotary support ? Comes supplied with 2 each: 6mm clamping studs-2 3/8" long, T-nuts, clamping straps and steps ? This remarkable little rotary table is priced affordably, too! ? Approx. weight: 9 lbs.

Siena Bronze table lamp features beautiful open work carving and a tall, polyresin classic silhouette. A bronze Tassel and an open sided hand carved finial add a sophisticated touch. The classic shade, with its coordinating gold and bronze trim adds to the timeless appeal of this piece. On / Off Rotary switch takes 100 Watts Bulb. 6' Brown Cord.12.5. Finish: Siena Bronze. Material: Polyresin. Lamping: 100W incandescent, with On/Off switch (rotary) (bulb NOT included).

SHARS HIGH PRECISION 12" TILTING TILT MT4 ROTARY TABLE NEW Product Code 202-2011 Product description Diameter: 12" Table height: 10.04" Center height: 6.89" Center plug recess: 1.6" Center bore MT4 Maximum individual spacing error: 60" Tilting Angle: 0-90 degree Product features High precision bearing surfaces ensure ultra smooth rotation Precision ground to meet the most exacting toolroom requirements Worm gear is easily disengaged for free rotation Graduates in seconds Gear ratio is 90:1

Unique 6-slot design Mounts horizontally or vertically Satin chrome handwheel and dial Dual table locks MT #1 socket, Manufacturer: South Bend Lathe

4 HOR/VER PHASE II ROTARY TABLE

Ideal for wherever space is at a premium, the Table Edge Rotary Trimmer has the same unique design features as the Advanced Rotary Trimmer, but with pre- drilledcounter- sunk holes for mounting flush to the edge and surface of your existing table. Materials on wall-mounted roll feeders can be easily measured on the table surface then trimmed to size. Available in lengths up to 10 feet, mount a cutter on both the X and Y axis of your existing table for trimming large sheetswithout excessive handling.