CalDigit HDPro2 holds 8 hot swappable drive modules in a desktop tower; optional rack mount kits are available. The hot swappable functionality of the HDPro2 allows users to upgrade the drive s capacity as needed while remaining very easy to configure. There is no capacity limitation to any single chassis. The CalDigit HDPro2 offers the best gigabyte-per-dolla r ratio in the world for hardware RAID storage. The HDPro2 is a high-performance storage solution with capacities from 8TB to 16TB. At under $1 per gigabyte including the PCI card and all required accessories - it s a fraction of the cost compared to other products in its class. The CalDigit HDPro2 uses SATA 3Gb/s drives with up to 32MB cache this means performance that meets the needs of the most demanding video and content editing... Less

Cache/Memory Installed - 128MB. Supporting Devices - 2. Interface Type - PCI-Express. Depth 7.3 . Height 2.7 . Controller Interface Type Serial ATA-300. Data Transfer Rate 300 MBps. Buffer Size 128 MB (installed) / 512 MB (max). Supported Devices Hard drive disk array (RAID). RAID Level RAID 0 RAID 1 JBOD. Processor AMCC PowerPC 405CR.

Specifications. Mfr Part Number: 9650SE-8LPML SGL. Features: . 8th-generation StorSwitch non-blocking switched architecture. On-board I/O RISC processor and RAID offload provides true hardware RAID: SCSI device driver model to take advantage of the benefits of SCSI using inexpensive Serial ATA drives. Bootable array support for greater fault tolerance. Variable stripe size for performance tuning by application. 64-bit LBA support. ATA pass-through mode support. 256MB DDR2-533 memory with ECC protection. 32 pooled DMA channels. Complete configuration management suite: . 3ware BIOS Manager 2 (3BM2) - easy to use BIOS configuration tool. 3ware Disk Manager 2 (3DM2) - browser-based management tool. Command Line Interface (CLI) - scriptable configuration tool . SNMP support. SMTP support for... Less

Specifications. Mfr Part Number: 9650SE-4LPML KIT. Features: . 8th-generation StorSwitch non-blocking switched architecture. On-board I/O RISC processor and RAID offload provides true hardware RAID: SCSI device driver model to take advantage of the benefits of SCSI using inexpensive Serial ATA drives. Bootable array support for greater fault tolerance. Variable stripe size for performance tuning by application. 64-bit LBA support. ATA pass-through mode support. 256MB DDR2-533 memory with ECC protection. 32 pooled DMA channels. Complete configuration management suite: . 3ware BIOS Manager 2 (3BM2) - easy to use BIOS configuration tool. 3ware Disk Manager 2 (3DM2) - browser-based management tool. Command Line Interface (CLI) - scriptable configuration tool . SNMP support. SMTP support for... Less

The Oakton Eutech 56705-00, 115V, pH 800 controller/transm itter has a 1/4 DIN-sized housing, dual-display, backlit LCD, on/off control, and push-button calibration. A pH controller/transm itter is used to measure pH, mV, and temperature of a substance in water purification or treatment, chemical processing, food processing, aquarium, pharmaceutical, hydroponics, and waste-control industries. This controller is selectable for pH or Oxidation Reduction Potential (ORP), features a dual-display LCD screen to guide programming and display indicators, and a nonvolatile memory to maintain setup if power fails. It has a programmable delay at 0 to 2,000 seconds to minimize false alarms. It has manual or ATC, and push-button operation with calibration at two set points for ease of use. Its 1/4... Less

Host Interface: PCI Express x 8. Data Transfer Rate: 300MBps. Standard Memory: 512MB. Embedded ECC DDR2. Form Factor: Low-profile Plug-in Card. Dimensions: 6.6 Width.

PCI 2-channel Serial-ATA host controller card. With optional software RAID function. The most popular version of 2-channel Serial-ATA host controller add-on card with optional RAID 0 1 function. PCI Specification Revision 2.2 compliant. Silicon Image SIL 3512 host controller chip. Support 66 Mhz PCI with 32-bit data. Compliant with programming interface for Bus Master IDE Controller Rev1.0. Support programmable and EEPROM FLASH & EPROM loadable PCI class mode. Integrated SATA Transport Link Logic & PHY layer. 48-bit sector addressing. Virtual DMA. Serial ATA Specification Revision 1.0 compliant. Dual independent DMA channels with 256KB FIFO per Serial-ATA channel transfer rate up to 1.5Gb/s. Internal Serial-ATA port x 2. Software Requirement: MS Windows 98SE/ME/NT4/2000/ XP/Server2003/XP6... Less

New Page 2 Remote DTMF Controllers - Controls Door Strikes and Gate Openers From a Touch Tone Phone. Designed for use with W-1000/2000/3000 Doorboxes or as a stand-alone 'Dial-up' remote Touch Tone controller. This unit can operate door strikes, gate openers, or control equipment at remote locations (the RC-2A and RC-3 can answer a ringing line) using a Touch Tone phone. The RC-2A can activate 1 momentary or maintained relay closure while the RC-3 can provide 3 relay contacts. Three RC-3s can be connected to the same line for 9 outputs. Tones confirm relay action. Either unit can be set up to operate with or without security codes. The RC-3 has a built-in pulse dialer activated by an external alarm contact. The RC-3 will dial a number up to three times, sending alert tones. (Power supply... Less

Platform: Dreamcast Aug 2001 Genre: Fighting Games ESRB Rating: Teen Publisher: Agetec, Inc. 1-2 Players Gamepad Warnings: Animated Violence, Violence Description The battle is on, and you're not about to let some two-bit punk tell you what's what. Choose from a list of 16 unique combatants and get ready to prove your worthiness in this detailed fighter for the Dreamcast. You decide whether you'd like your warrior to specialize in speed, power, or a combination of the two. The game combines incredible cartoon-style graphics and state-of-the-art gameplay to deliver a strategy-heavy fighting game that's as unique as it is addicting., The battle is on, and you're not about to let some two-bit punk tell you what's what. Choose from a list of 16 unique combatants and get ready to prove... Less

The SNAP-PAC-R2 programmable automation controller provides control, communication, and I/O processing in a compact, rack-mounted package. One of four components of the SNAP PAC System, the SNAP-PAC-R2 is fully integrated with PAC Project software, SNAP PAC brains, and SNAP I/O modules. Used with the included PAC Project Basic software suite (or PAC Project Professional, purchased separately), the Ethernet-based SNAP-PAC-R2 can handle almost all your industrial control, remote monitoring, and data acquisition needs. This intelligent, flexible PAC can be used in several ways. The SNAP-PAC-R2 can provide complete cell control on its own rack with I/O modules. It can also control SNAP PAC I/O units at the same time for a larger system. Or the R2 can be used in a more extensive distributed... Less