> jabsco water puppy general purpose pump

Commercial Duty Water PuppyFlow rate: 34 litres/min (9 USgallons/min) Self-priming from dry up to 1.2m (4ft)Features:Smal l bilge debris present no problem to these bronze bodied, flexible impeller pumps.Simple design means fewer wearing parts.ISO 8846 MARINE (Ignition protection).ISO 8849 MARINE (Bilge pump standard). MotorPermanent magnet type, fully enclosed, stainless steel shaft, ball type shaft bearing, has adequate torque to reverse the pump Port Type1/2" Internal Pipe Threads 1" External Hose Barb Adapter for 3/4 " External Garden Hose Thread included

Fresh Water PumpElectic Water System Pump, Automatic, Multi-OutletFlow rate: Nominal 3 gallons/min at 1500 rpmSelf-priming from dry up to 4.9ftFeatures: Diaphragm Design Allows Dry RunningBuilt-in Discharge Check ValveQuiet OperationBuilt- in Hydraulic Pulsation DampenerLarge Vibration Absorbing PadsPorts Available with Barb, Threads or FlareMeets USCG Regulation 183.410ISO 8846 MARINE for Ignition Protection Jabsco automatic water system pumps are designed for self contained recreational vehicles and pleasure boats with multiple-outlet water systems. The systems are automatic -when a faucet is opened, the pump instantly begins operation to provide a constant flow from tank to faucet. Closing the faucet automatically discontinues pump operation.

2" Bronze Pedestal PumpFlow rate: Nominal 60 gallons/min at 1500 rpmSelf-priming from dry up to 7.8ftFeatures: Constructed from marine quality bronze and stainless steel for ruggedness and reliability.Easy to service and maintain. Inexpensive to buy and operate.Will tolerate abrasive wear (this may affect performance - seek advice from your distributor). Handles hard and soft solids without clogging.Can pump in either direction.Will not airlock. APPLICATIONSMARIN E:Engine cooling, pumping bilges, wash downs, circulating water in bait tanks, utility dock side pump. INDUSTRIAL: Circulating and transferring, Velocity-mixing, Return spill, Sump drainage, Chemicals, Pharmaceuticals, Soap, Liquors, Inks, Dyes, Alcohol, Tanning Liquors, Glycerin, Brine, etc.FARMING:Pumpin g water for stock, Pumping water from shallow wells and cisterns.

Diaphragm Bilge PumpFlow rate: Nominal 8 gallons/minSelf- priming from dry up to 7.8ftFeatures: Diaphragm Design Allows Dry Running.Quiet Operation. Permanently Lubricated Ball Bearings on Shaft and Connecting Rod.Large Vibration Absorbing Pads.Corrosion Resistant Materials Throughout for Sea Water Service.Meets USCG Regulation 183.410 and ISO 8846 MARINE for Ignition ProtectionJabsco automatic water system pumps are designed for self contained recreational vehicles and pleasure boats with multiple-outlet water systems. The systems are automatic -when a faucet is opened, the pump instantly begins operation to provide a constant flow from tank to faucet. Closing the faucet automatically discontinues pump operation.

PAR 36800 Water Pressure PumpThis well established and service proven pump will serve up to 4 outlets simultaneously and generously3.3 gpm open flow outputSelf- primingHigh pressure switch cut-in 20 psi (1.4 bar), cut-out 40 psi (2.8 bar)Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection) Connections for 1/2" - 5/8" ID Hose.

Jabsco Wakeboard Ballast Puppy w Reversing Switch 12vBallast PumpTodays Wakeboard and Ski tow boats need to be able to take on water ballast to modify their wake formation. A development of our tried and tested Puppy Pumps lets these specialist c...

Ballast PumpToday's Wakeboard and Ski tow boats need to be able to take on water ballast to modify their wake formation. A development of our tried and tested Puppy Pumps lets these specialist craft rapidly take on and dump ballast, while modern electronics guard against dry running damage to the impellerThe choice of motor boat builders for ski and wakeboard ballast systems.Unique impeller compountHandles debrisReversible8 GPM flowEasy service

PAR-Max 2.9 2.9 GPM Water Pressure System Pumps Features: Smooth flow Dry running capability Soft noise absorbing mounts Snap-fit port fittings Built-in bypass - less pulsation Reduces need for accumulator tank Corrosion resistant materials...

Manufacturer id:31600-0092 PAR-Max 3 Water Pressure System Pump Features:Smooth Flow Dry running capability Soft noise absorbing mounts Snap-fit port fittings Corrosion resistant materials Meets USCG Regulation 183.410 and ISO 8846 MARINE (ignition protection)Meets EN 50081-1 Electro-magnetic Compatibility Product : JABSCO PARMAX 3 HIGH PRESSURE 3 OUTLET WATER PUMP 3.5PGM Manufacturer : JABSCO Manufacturer Part No : 31600-0092 UPC : 671880533133 Please be sure to read the description and ask qu

Manufacturer id:31600-0292 PAR-Max 3 Water Pressure System Pump Features:Smooth Flow Dry running capability Soft noise absorbing mounts Snap-fit port fittings Corrosion resistant materials Meets USCG Regulation 183.410 and ISO 8846 MARINE (ignition protection)Meets EN 50081-1 Electro-magnetic Compatibility Product : JABSCO PARMAX 3 LOW PRESSURE 3 OUTLET WATER PUMP 3.5GPM Manufacturer : JABSCO Manufacturer Part No : 31600-0292 UPC : 671880533157 Please be sure to read the description and ask que

This is a low stock or special order item. It is possible for us to run out of stock so if you need this item right away please contact us to check stock first. Manufacturer id:18670-0123 Commercial Duty Water Puppy Flow rate: 34 litres/min (9 USgallons/min) Self-priming from dry up to 1.2m (4ft)Features:Smal l bilge debris present no problem to these bronze bodied, flexible impeller pumps.Simple design means fewer wearing parts.ISO 8846 MARINE (Ignition protection).ISO 8849 MARINE (Bilge pump sta

Johnson Pumps Crank Shaft Pulley Mounted Pump - V8 VOLVO ENGINE PUMP F6B11

Manufacturer id:18670-0943 Commercial Duty Water Puppy Flow rate: 34 litres/min (9 USgallons/min) Self-priming from dry up to 1.2m (4ft)Features:Smal l bilge debris present no problem to these bronze bodied, flexible impeller pumps.Simple design means fewer wearing parts.ISO 8846 MARINE (Ignition protection).ISO 8849 MARINE (Bilge pump standard). Motor Permanent magnet type, fully enclosed, stainless steel shaft, ball type shaft bearing, has adequate torque to reverse the pump Port Type 1/2" Inte

PAR-Max 3 Water Pressure System Pump Features: Smooth Flow Dry running capability Soft noise absorbing mounts Snap-fit port fittings Corrosion resistant materials Meets USCG Regulation 183.410 and ISO 8846 MARINE (ignition protection) Meets...

sealed maceratorself- priming macerator pump with run-dry protectionwaste evacuationthe jabsco 18590 series dc macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. self priming to 5ft this pump will empty a typical 30 gallon (115 liter) holding tank in less than 3 minutes. duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operationit is recommended that holding tanks be flushed with several gallons of water after each pump out. this will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage.fish box and livewell tank evacuationthe jabsco macerator pump is the ideal pump for the emptying of fish box and livewell receptacles. very often the livewell tank will be above the waterline of the boat when this is the case gravity can be used to empty the livewell tank. if not installed in this format then it is beneficial to use the jabsco macerator pump for evacuation due to its self-priming capabilities and also it s grinding properties.fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. again the jabsco macerator pump has the characteristics that lend themselves to this application. the bait residue particles of ice fish scales and anything else that could potentially be found in the fish-box will be easily passed buy the jabsco macerator pump and the self priming capabilities are perfect for fish box installations common to many of today s sports fishing boats.features: impeller: jabsco nitrile compound macerator: stainless steel cutter reduces particle size to 1/8" maximum. new 4 blade designseal: lip typeproduct : jabsco 12v sealed macerator pump 1-1/2" in - 1" out manufacturer : jabsco manufacturer part no : 18590-2092 upc : 671880564373

31705 Bilge and Shower Drain Pump Bilge/Livewell/Ge neral Purpose Diaphragm Pump Features: Self-Priming from dry up to 2.4m (7.8ft) Run dry without damage Smooth flow Four piston, diaphragm pump Powerful heavy duty motor with Thermal Overload ...

PAR-Max 4 Water Pressure System Pump Features: Smooth flow Dry running capability Soft noise absorbing mounts Snap-fit port fittings Corrosion resistant materials Meets USCG Regulation 183.410 and ISO 8846 MARINE (ignition protection) Meets...

PAR-Max 3 Water Pressure System Pump Features: Smooth Flow Dry running capability Soft noise absorbing mounts Snap-fit port fittings Corrosion resistant materials Meets USCG Regulation 183.410 and ISO 8846 MARINE (ignition protection) Meets...

This compact high-pressure pump features a powerful 3.5 gpm flow rate to blast mud and silt from your anchor chain and deck. Waterproof design includes coated motor and sealed pressure switch. Thermal overload protection automatically stops the motor if it overheats. Comes with Pumpgard filter, trigger nozzle, and snap-in ports. Self-priming up to 10 ft. Connections for 1/2" ID hose. 12V DC. 10 amp fuse. 8.6"L x 4.2"W x 4.1"H.

Sensor Max VSD Pump Features: Self-priming from dry up to 2.4m (7.8ft) Variable Speed Control Solid State Pressure Sensor Nearly Silent Operation / No Cycling Controls Pressure by Changing Motor Speed Speeds up as demand increases Self-prim...

Engine Oil Drain Pump Polished brass hand pump connects directly to engine oil dipstick tube on many popular marine engines such as OMC and Mercruiser Screws onto threaded male 3/4" garden hose (GHT) fitting on top of dipstick tube. Gives simple ...

Manufacturer id:18220-1127 Ballast Pump Today's Wakeboard and Ski tow boats need to be able to take on water ballast to modify their wake formation. A development of our tried and tested Puppy Pumps lets these specialist craft rapidly take on and dump ballast, while modern electronics guard against dry running damage to the impeller The choice of motor boat builders for ski and wakeboard ballast systems.Unique impeller compount Handles debris Reversible 8 GPM flow Easy service Product : JABSCO

Accumulator TankThis Accumulator Tank is intended for installation in any pumped water system controlled by a pressure switch. For example, PAR-MATE 2.5 or any Jabsco pressure pumps as found in boats, RV's, motor caravans, coaches and similar applications.The Accumulator Tank smoothes water flow and reduces on/off cycling of the pump by lessening the variation in pressure and flow between the pump and the outlets in the system.The even flow of water gives better control of hot water temperature especially noticeable with instantaneous gas water heaters and with showers.The reduced on/off cycling reduces noise from the pump motor, and from shock pressures (pipe hammer). It also reduces battery drain, and gives longer pump life.Features: Internal BladderSmoother and More Even FlowQuieter Water SystemBetter Temperature ControlLonger Pump lifeLower battery DrainSimply fitted to new or existing systemsCompact sizeSnap-in port fittings include both: 1/2" barbed hose fittings and 1/2" threaded hose fittingsTank: hygienic, light, compact, impact and pressure resistant plastic construction

Drill PumpsJabsco drill pumps provide a very versatile means of transferring fluid almost anywhere an electric drill with 1/4" to 3/8" chuck can be operated. They provide easy powered pumping almost anywhere a hand utility pump might be used.Pumps up to 3.5 gpmSelf-priming to 3ft1/4" diameter shaftSupplied with 3/4" garden hose thread port adapters

Sealed MaceratorSelf- Priming Macerator Pump with Run-Dry ProtectionWaste EvacuationThe Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operationIt is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage.Fish Box and Livewell Tank EvacuationThe Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties.Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats.Features: Impeller: Jabsco Nitrile compound Macerator: Stainless Steel Cutter reduces particle size to 1/8" maximum. New 4 blade designSeal: Lip Type

Low Pressure Cyclone Centrifugal Pump"Cyclone Pump" Stainless Steel DC Motor/Pump UnitFlow rate: 29.7 gallons/minPressu re up to 8.7psiFeatures: Heavy duty robust stainless steel constructionOne tool servicing (3/8" Spanner) Virtually silent running centrifugal pumpLong-life DC motorRotatable head 90segmentsAnti- clogging impeller designLong-life mechanical sealISO 8846 MARINE and USCG Regulations for Ignition Protection.ISO 8849 MARINE Bilge Pump Standard

Drill PumpsJabsco drill pumps provide a very versatile means of transferring fluid almost anywhere an electric drill with 1/4" to 3/8" chuck can be operated. They provide easy powered pumping almost anywhere a hand utility pump might be used.Pumps up to 3.5 gpmSelf-priming to 3ft1/4" diameter shaftSupplied with 3/4" garden hose thread port adapters

Sealed MaceratorSelf- Priming Macerator Pump with Run-Dry ProtectionWaste EvacuationThe Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operationIt is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage.Fish Box and Livewell Tank EvacuationThe Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties.Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats.Features: Impeller: Jabsco Nitrile compound Macerator: Stainless Steel Cutter reduces particle size to 1/8" maximum. New 4 blade designSeal: Lip Type MP Master List

Utility PumpThe 6050-Series pumps are the highest capacity, self-priming, portable Utility Pumps offered by JabscoBronze pump head23 GPM output at 10ft total headContinuous duty motor with thermal over-load protectionMotor wired to operate with 115v and can be converted to 230vOpen drip proof motor8' power cord with grounded plugconvenient carrying handle

Little Pal Utility Pump Compact polished brass multi-purpose hand pump Ideal for small engine and gearbox oil drain Simply pump old oil out with dipstick probe Oil and corrosion resistant brass and neoprene construction with up to 1 gpm output ...

Sensor Max VSD PumpsFeatures: Self-priming from dry up to 2.4m (7.8ft)Variable Speed ControlSolid State Pressure SensorNearly Silent Operation / No CyclingControls Pressure by Changing Motor SpeedSpeeds up as demand increasesSelf- priming / runs dryNo accumulator tank neededCSA listed / EN ISO 8846 Marine / C.E. CertifiedProtecte d under U.S. Patent #6,607,360Includes Inlet Strainer35 PSI Cut-Out

32700 Washdown & Baitwell Pump Features: High Pressure / High Capacity Suitable For Use With Salt Water Long Life Sealed Motor Dry Running Capability Corrosion Resistant Pump Body - Glass Filled Polypropylene Pump Design - 4 Chamber Diaphra...

Manufacturer id:34060-0010 Little Pal Utility Pump Compact polished brass multi-purpose hand pump Ideal for small engine and gearbox oil drain Simply pump old oil out with dipstick probe Oil and corrosion resistant brass and neoprene construction with up to 1 gpm output Small enough to fit any tool box Product : JABSCO 10-1/4" UTILITY HAND PUMP 4-5/8" DIAMETER 40 SPG Manufacturer : JABSCO Manufacturer Part No : 34060-0010 UPC : 671880028622 Please be sure to read the description and ask questio

Drill Pumps Jabsco drill pumps provide a very versatile means of transferring fluid almost anywhere an electric drill with 1/4" to 3/8" chuck can be operated. They provide easy powered pumping almost anywhere a hand utility pump might be used. Pum...

31705 Bilge and Shower Drain PumpBilge/Livewel l/General Purpose Diaphragm PumpFeatures: Self-Priming from dry up to 2.4m (7.8ft)Run dry without damageSmooth flowFour piston, diaphragm pumpPowerful heavy duty motor with Thermal Overload ProtectionSnap- in PortsWaterproof coatingMeets USCG Regulation 183.410 and EN ISO 8846 MARINE (Ignition Protection Standards)Meets EN 50081-1 Electro-magnetic CompatiblityCompl ies with EN ISO 8849 MARINE Electric Bilge Pump

PAR-Max 2.92.9 GPM Water Pressure System PumpsFeatures: Smooth flowDry running capabilitySoft noise absorbing mountsSnap-fit port fittingsBuilt-in bypass - less pulsationReduces need for accumulator tankCorrosion resistant materialsCSA listedISO 8846 MARINE (ignition protection)CE

Lite Flush 12V Toilet With Control PanelA NEW Electric Toilet designed to instantly retro-fit your existing manual toilet or to give your bathroom a modern stylish look. The innovative design offers both low power and water consumption with an integral rinse and waste pump system. Internally mounted, high speed, non-clogging, centrifugal, waste macerating pump driven by powerful 240 watt, 12 or 24 Vdc, permanent magnet motor with ball bearings and robust ceramic seal, discharges up to 5ft (1.5m) above the base of the toilet. Jabsco, self-priming up to 3m (10ft), dry running, diaphragm water pump driven by 12 or 24 Vdc, permanent magnet, ball bearing motor. Integral one touch 'Press and Release' switch pad, sealed for life. One Touch 'Press and Release' switch pad, sealed for life, with 10ft (3m) link cable, fitted quick connector, and heat shrink seal. Complies with ISO8846 MARINE (Ignition Protection). Raw Water Rinse pump inlet 3/4" (19mm) hose tails. Flush pump discharge 1-1/2" (38mm) hose tail.Features: Space saving stylish design Compact size, rotatable seat Virtually silent operation Choice of leaving bowl wet or dry after use Non-clogging large bore flush pump macerates waste Uses less than 1.0 amp/hour per day ISO 8846 MARINE Ignition Protection

This Accumulator Tank is intended for installation in any pumped water system controlled by a pressure switch. For example, PAR-MATE 2.5 or any Jabsco pressure pumps as found in boats, RV's, motor caravans, coaches and similar applications. The Accumulator Tank smooths water flow and reduces on/off cycling of the pump by lessening the variation in pressure and flow between the pump and the outlets in the system. The even flow of water gives better control of hot water temperature especially noticeable with instantaneous gas water heaters and with showers. The reduced on/off cycling reduces noise from the pump motor, and from shock pressures (pipe hammer). It alsoreduces battery drain, and gives longer pump life. Features: Internal Bladder Smoother and More Even Flow Quieter Water System Better Temperature Control Longer Pump Life Lower Battery Drain Simply Fitted to New or Existing Systems Compact Size Snap-in Port Fittings include both:1/2" Barbed Hose Fittings and1/2" Threaded Hose Fittings Tank: Hygienic, Light, Compact,Impact and Pressure ResistantPlastic Construction Specifications: Capacity: 1 Litre 33 fl oz Regulated Pressure: 8.6 bar 125 psi Pre-Charged Pressure: 0.7 bar 10 psi Weight: 1.6 lb 0.7 kg Dimensions: 33.7 x 11.9 cms 13-1/4 x 4-3/4 inches

Waste PumpRobust Single Diaphragm DesignFeatures: Flexible installationNo filter requiredCompact and simple designDry running capabilityConnect ions for 38mm (1 1/2") portsUp to 19 lpm (5 US gpm) flowRelevant Standards: ISO 8846 MARINE and USCG Regulations for Ignition Protection ISO 8849 MARINE Bilge Pump StandardBuilt to ISO 15083 SpecificationMeet s BSEN 50081 (Electro Magnetic Compatibility)